GE AKTAprocess Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 180

GE AKTAprocess Скачать руководство пользователя страница 118

5.1.3

Priming and leakage test

Introduction

Before a run is started the system should be primed and tested for possible leakage.
This section describes a procedure for priming and testing for leakage.

Important

NOTICE

All system parts must be correctly filled with liquid before any
functional tests are performed. A suitable liquid is a storage or
running buffer for the column.

NOTICE

During the procedure described below, check all valves and tubing
connections carefully for air or liquid leakage. If there is any evi-
dence of leakage, attend to the leak and then repeat the filling se-
quence.

Each pump must be tested separately if more than one is used (Optional Gra-
dient pump B and/or Sample pump in addition to the standard pump A).

Note:

Prepare for priming and leakage
test

Follow the instruction below to prepare ÄKTAprocess for priming and leakage test.

Action

Step

Check that the inlet and outlet tubing are correctly connected.

1

Check that the buffer tank(s) are filled with a sufficient amount of a suitable
liquid for the procedure.

2

Check that valves to the buffer tanks are open.

3

118

ÄKTAprocess Operating Instructions 29-0252-49 AA

5 Operation

5.1 Prepare the system
5.1.3 Priming and leakage test

«
...
116
117
118
119
120
...
»

Содержание AKTAprocess





















































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды