background image

 

Copyright

Copyright © 2005, GE Security Inc. All rights reserved. 

This document may not be copied in whole or in part, or otherwise reproduced except as 

specifically permitted under US copyright law, without the prior written consent from GE. 

Document number/revision: 466-2204B. 

Disclaimer

The information in this document is subject to change without notice. GE, in keeping pace with 

technological advances, is a company of product innovation. Therefore, it is difficult to ensure 

that all information provided is entirely accurate and up-to-date. GE accepts no responsibility 

for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal 

or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any 

of the contents of this document. 

This publication may contain examples of screen captures and reports used in daily operations. 

Examples may include fictitious names of individuals and companies. Any similarity to names 

and addresses of actual businesses or persons is entirely coincidental. 

Trademarks and patents

GE and the GE monogram are registered trademarks of General Electric. 

Other trade names used in this document may be trademarks or registered trademarks of the 

manufacturers or vendors of the respective products. 

Software license agreement

GE software supplied with GE products is proprietary and furnished under license and can be 

used or copied only in accordance with the license terms. 

THE ENCLOSED PROGRAM IS FURNISHED SUBJECT TO THE TERMS AND CONDITIONS OF THIS 

AGREEMENT. RETENTION OF THE PROGRAM FOR MORE THAN 30 DAYS, OPENING OF THE SEALED 

WRAPPER, IF ANY, SURROUNDING THE PROGRAM, OR USE OF THE PROGRAM IN ANY MANNER 

WILL BE CONSIDERED ACCEPTANCE OF THE AGREEMENT TERMS. IF THESE TERMS ARE NOT 

ACCEPTABLE, RETURN THE UNUSED PROGRAM AND ANY ACCOMPANYING DOCUMENTATION TO 

GE FOR A FULL REFUND OF THE LICENSE FEE PAID. (FOR INFORMATION REGARDING THE RETURN 

OF PROGRAMS ENCODED OR INCORPORATED WITHIN EQUIPMENT, CONTACT THE NEAREST GE 

SALES OFFICE.) 

Intended use

Use this product only for the purpose for which it was designed; refer to the data sheet and user 

documentation. For the latest product information, contact your GE sales representative or visit 

us online at 

www.gesecurity.com

FCC compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference when the equipment is operated in a commercial environment. 

This equipment generates, uses, and can radiate radio frequency energy and, if not installed 

and used in accordance with the instruction manual, may cause harmful interference to radio 

communications. 

You are cautioned that any changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to operate the equipment. 

Contact

Direct all inquiries about GE’s legal policies with regard to this product to: 

Director of Legal Services

GE Security

12345 SW Leveton Drive

Tualatin, OR 97062-9938 USA

Содержание NX-592E





















Отзывы: