GDS GDS 550P Series Скачать руководство пользователя

Страница: 7 / 15

Electrical Connections

PERATORS

•

20mm conduit for mains voltage and conduit for low voltage cabling can enter from either side (see cut out
positions on cover) or preferably from the spacing between plate & operator cover.

•

Wire the mains voltage cabling straight to the motor terminals and connect both the shield and earth to the
earth terminal.

•

Wire the low voltage cables to the door switch. If the cabling run is over 8m, connect the shield to the earthed
chassis.

Connections to Control Board

Supply

Connect a 10A 240v non earth leakage protected power supply to Din Rail terminals labelled A & N
Connect earth to the earth Din Rail

Motor Wires

Connect the shielded motor cable to Inverter terminals. Connect earth and shield to Earth Stud.

Содержание GDS 550P Series
















Результаты поиска

Содержание GDS 550P Series

Отзывы:

Похожие инструкции для GDS 550P Series

Бренды по названию

Популярные бренды

GDS GDS 550P Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание GDS 550P Series

Отзывы:

Похожие инструкции для GDS 550P Series

Бренды по названию

Популярные бренды