GCC Technologies P3-132S Скачать руководство пользователя

Страница: 78 / 179

Puma III User Manual

Trouble Shooting 7-1

Chapter 7 Trouble Shooting

This chapter is to help you correct some common problems you may come across. Prior to

getting into the details of this chapter, please be sure that your application environment is

compatible with the cutting plotter.

Possible Causes:

7.1 Non-Operational Problems

Check the following first:



Does the AC power cord plug in properly?



Does the AC power cord connected to the power connector properly?



Does the power LED still illuminate?

Solutions:

If the LCM is able to display the message, the cutting plotter should be in a normal

condition. Switch off the cutting plotter and turn it on again to see if the problem still

existing.

If the LCM is not able to display any message, contact the technician from your dealer.

Note:

Before having your cutting plotter serviced, please

make sure that the malfunction is in your cutting

plotter, not the result of an interface problem or a

malfunction in your computer or a software problem.

Why doesn’t the cutting plotter operate?

Содержание P3-132S




















































































































































































Результаты поиска

Содержание P3-132S

Отзывы:

Похожие инструкции для P3-132S

Бренды по названию

Популярные бренды

GCC Technologies P3-132S, Руководство пользователя

Результаты поиска

Содержание P3-132S

Отзывы:

Похожие инструкции для P3-132S

Бренды по названию

Популярные бренды