background image

Page 5 of 25

Section 

3  SAFETY DIRECTIONS & WARRANTY 

3.1 

General 

The following directions should enable the person responsible for the product, and 
the person responsible for use of the equipment, to anticipate and avoid operational 
hazards. 

The person responsible for the product must ensure that all personnel who install 
and maintain the product understand these directions and adhere to them. 

3.2 

Intended Use 

Permitted Uses

 

Bill Note Validation 

Adverse Uses

 

Adverse uses of the equipment include, but are not limited to: 

Use of the product without instruction

Use outside of the intended limits

Removal of hazard notices

Opening the product while it is connected to mains power

Modification or conversion of the product

Use of products with obviously recognizable damages or defects

 Warning

 

Adverse use can lead to injury, malfunction and damage.   
It is the task of the person responsible for the equipment to 
inform the user about hazards and how to counteract them. The 
product is not to be operated until the user has been instructed 
on how to work with it. 

3.3 

Responsibilities 

Person 
installing or 
maintaining 
the product

 

The person installing or maintaining the product has the 
following duties: 

To understand the safety instructions on the product and the
instructions in the user manual 

To be familiar with local regulations relating to safety and accident
prevention

To inform relevant person in charge immediately if the product and
the application becomes unsafe

To ensure that the national laws, regulations and conditions for the

operation are respected

 Warning

 

The person installing the product must ensure that the product 
is used for its intended purpose and that it is operationally safe. 

 Warning

 

This product may be installed only by an appropriately trained 
and qualified technician as per any national regulation. 

 Warning

 

Only Astrosys International authorized service workshops are 
entitled to repair these products. 

www.TURNSTILES.us / www.entrapass.com / 8641 S. Warhawk Road, Conifer, CO 80433 / 303-670-1099

Содержание ST1C-UL


























Отзывы: