Gateway 930 series Скачать руководство пользователя страница 123

Страница: 123 / 160

Memory and processor problems

115

Memory and processor problems

The system detected memory errors during start up.

The system does not recognize a new or second processor.

Probable cause

Solution

Memory was added or
removed, and the new
configuration was not saved
in BIOS Setup utility

Open the BIOS Setup utility and save the new
memory configuration.

The memory was installed
incorrectly

Make sure the memory is seated and oriented
correctly.

A memory chip is faulty

Replace the card with the faulty chip.
Third-party diagnostic programs can help
determine which chip or memory segment is
failing.

Probable cause

Solution

The processor was installed
incorrectly or was not seated
correctly in the socket

Check the installation and make sure the
processor is fully seated in the socket. The
processor should be recognized automatically
if it was installed correctly.

8508088.book Page 115 Thursday, November 1, 2001 9:35 AM

Содержание 930 series

































































































































































Результаты поиска

Содержание 930 series

Отзывы:

Похожие инструкции для 930 series

Бренды по названию

Популярные бренды

Gateway 930 series, Системное руководство

Результаты поиска

Содержание 930 series

Отзывы:

Похожие инструкции для 930 series

Бренды по названию

Популярные бренды