Gateway 930 series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 160

background image

Front panel

3

PS 1 status LED

glows green when the first power supply module in the

redundant power supply is installed and working correctly. The LED is off if
the power supply module fails or if the power supply module is not installed.

PS 2 status LED

glows green when the second power supply module in the

redundant power supply is installed and working correctly. The LED is off if
the power supply module fails or if the power supply module is not installed.

System reset button

is a recessed button that lets you reset the server if it

becomes nonresponsive.

Power button

turns the server on and off. In an ACPI-enabled operating

system like Windows 2000, you can set the power button to enter sleep mode
rather than turn the system off.

Hot-plug drive lock

secures the drive in place to prevent unauthorized or

accidental removal.

Outriggers

provide support for the castors.

Castors

let you roll the server around for ease of service.

5.25-inch drive bays (3)

have room for additional 5.25-inch devices such as

tape drives or an additional CD drive.

CD drive

plays data or audio CDs.

Diskette drive

writes to and reads from 3.5-inch, 1.44 MB diskettes.

System fault LED reset switch

resets the system fault LED, if it is flashing.

The appropriate LED continues to flash until the failed power supply module
is replaced.

Hot-plug drive activity LED

indicates when the hot-plug drive immediately

below it is reading or writing data.

Hot-plug drive bay

has room for as many as six hot-plug drives connected

to a hot-plug backplane. Drives have to be set up in appropriate RAID
configuration to be hot-pluggable. Removing a drive when it is not properly
configured will result in lost data and may corrupt the operating system.

Front panel door

covers the front panel controls to prevent unauthorized or

accidental access.

8508088.book Page 3 Thursday, November 1, 2001 9:35 AM

«
...
9
10
11
12
13
...
»

Содержание 930 series

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 930 series

Бренд: Mako Страницы: 56

Бренд: NComputing Страницы: 95

Бренд: IBM Страницы: 40

Power 720 Express 8202-E4B

Бренд: IBM Страницы: 64

Бренд: IBM Страницы: 148

Бренд: IBM Страницы: 36

Бренд: IBM Страницы: 834

Бренд: ACTi Страницы: 15

Бренд: Sun Oracle Страницы: 222

Netfinity 3500 Series

Бренд: IBM Страницы: 152

xPort Pro XPP1004000-02R

Бренд: Lantronix Страницы: 17

Бренд: BlueNet Video Страницы: 38

CE-HE130S4 Series

Бренд: Ablecom Страницы: 43

SUPERSERVER 1015B-3

Бренд: Supermicro Страницы: 98

Бренд: Spectra Страницы: 184

Бренд: Imagine Страницы: 2

Бренд: ImageQuest Страницы: 31

Edgeline EL4000

Бренд: HPE Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды