Gatan 656 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 49

Gatan 656 Скачать руководство пользователя страница 17

Description

Dimple Grinder User’s Guide

7

Figure 5

Wheel types.

The following table presents the material and sizes of the different wheels:

Note:

The polishing rings have a limited lifetime and should be replaced regu-

larly. Take care not to get the felt polishing rings contaminated and do not mix
different polishing compounds on the same ring.

Caution:

Be careful to ensure that the male and female surfaces of the wheels

and axle assembly are kept clean. Do not flood the male taper with solvents to
clean the axle, as this may flush grit or compounds into the axle assembly lead-
ing to wear and impaired performance. Clean the axle with a lens tissue lightly

Wheels

Material

Edges

Size (mm)

Grinding

Phosphor bronze

Spherical

10
15 (standard)
20

Flat

15

Polishing

Male/female parts
supporting a felt ring

10
15 (standard)
20

Durlon rim

polishing wheel

10 mm, 15 mm,

and 20 mm

Dimple

wheel

axle

Spherical rim grinding wheel,
10 mm, 15 mm, and 20 mm
or
Flat rim, grinding wheel,
15 mm only

Dimple

wheel

axle

Thumb

screw

Thumb

screw

Felt
ring

Spherical

Grinding wheel

Flat

«
...
15
16
17
18
19
...
»

Содержание 656


















































Отзывы:

Нет отзывов