Garmin A03113, Руководство пользователя

Страница: 17 / 60

Lane Width : Specifies the width of the navigation lane, which is
the magenta line in some chart views that indicates the
course to your destination.
Other Vessels Settings on the Charts and Chart Views
NOTE: These options require connected accessories, such as
an AIS receiver or VHF radio.
From a chart or a 3D chart view, select
MENU > Other Vessels .
List : Shows a list of AIS and MARPA vessels.
DSC : Shows the DSC list and sets the DSC trails on the chart.
Collision Alarm : Sets the safe-zone collision alarm ( Setting the
Safe-Zone Collision Alarm , page 7 ).
Display Setup : See Showing AIS and MARPA Vessels on a
Chart or on a 3D Chart View , page 7 .
Laylines Settings
To use the laylines features, you must connect a wind sensor to
the chartplotter.
When in sailing mode (
Setting the Vessel Type , page 3 ), you
can display laylines on the navigation chart. Laylines can be
very helpful when racing.
From the navigation chart, select
MENU > Sailing > Laylines .
Display : Sets how the laylines and vessel appear on the chart,
and sets the length of the laylines.
Sailing Ang. : Allows you to select how the device calculates
laylines. The Actual option calculates the laylines using the
measured wind angle from the wind sensor. The Manual
option calculates the laylines using manually entered
windward and leeward angles.
Windward Ang. : Allows you to set a layline based on the
windward sailing angle.
Leeward Ang. : Allows you to set a layline based on the leeward
sailing angle.
Tide Correction : Corrects the laylines based on the tide.
Layline Filter : Filters the layline data based on the time interval
entered. For a smoother layline that filters out some of the
changes in the boat's heading or true wind angle, enter a
higher number. For laylines that display a higher sensitivity to
changes in the boat's heading or true wind angle, enter a
lower number.
Fish Eye 3D Settings
NOTE: This feature is available with premium charts, in some
areas.
From the Fish Eye 3D chart view, select MENU.
Fisheye View : Sets the perspective of the 3D chart view.
Tracks : Shows tracks.
Sonar Cone : Shows a cone that indicates the area covered by
the transducer.
Fish Symbols : Shows suspended targets.
Garmin Quickdraw
™
Contours
Mapping
WARNING
The Garmin Quickdraw Contours mapping feature allows users
to generate maps. Garmin makes no representations about the
accuracy, reliability, completeness or timeliness of the maps
generated by third parties. Any use or reliance on the maps
generated by third parties is at your own risk.
The Garmin Quickdraw Contours mapping feature allows you to
instantly create maps with contours and depth labels for any
body of water.
When Garmin Quickdraw Contours records data, a colored
circle surrounds the vessel icon. This circle represents the
approximate area of the map that is scanned by each pass.
A green circle indicates good depth and GPS position, and a
speed under 16 km/h (10 mph). A yellow circle indicates good
depth and GPS position, and a speed between 16 and 32 km/h
(10 and 20 mph). A red circle indicates poor depth or GPS
position, and a speed above 32 km/h (20 mph).
You can view Garmin Quickdraw Contours in a combination
screen or as a single view on the map.
The amount of saved data depends on the size of your memory
card, your sonar source, and the speed of your boat as you
record data. You can record longer when you use a single-beam
sonar. It is estimated that you might be able to record about
1,500 hours of data onto a 2 GB memory card.
When you record data on a memory card in your chartplotter,
the new data is added to your existing Garmin Quickdraw
Contours map, and is saved on the memory card. When you
insert a new memory card, the existing data does not transfer
onto the new card.
Mapping a Body of Water Using the Garmin
Quickdraw Contours Feature
Before you can use the Garmin Quickdraw Contours feature,
you must have a supported chartplotter with upgraded software,
sonar depth, your GPS position, and a memory card with free
space.
NOTE: This feature is not available on all models.
1
From a chart view, select MENU > Quickdraw Contours >
Start Recording .
2
When recording is complete, select Stop Recording .
3
Select Manage > Name , and enter a name for the map.
Adding a Label to a Garmin Quickdraw
Contours Map
You can add labels to a Garmin Quickdraw Contours map to
mark hazards or points of interest.
1
From the Navigation chart, select a location.
2
Select Add Quickdraw Label .
3
Enter text for the label, and select Done .
Garmin Quickdraw Community
The Garmin Quickdraw Community is a free, public, online
community that enables you to share your Garmin Quickdraw
Contours maps with others. You can also download maps other
users have created.
To access the Garmin Quickdraw Community, sign in to your
Garmin Connect
™
account, and then you can upload and
download maps using a memory card.
Accessing the Garmin Quickdraw Community
You can access the Garmin Quickdraw Community using
Garmin Connect website.
1
Go to connect.garmin.com .
2
Select Get Started > Quickdraw Community > Get Started .
Garmin Quickdraw
™
Contours Mapping 9