English
32/124
Do not perform this operation in an enclosed
or poorly ventilated.
Stay away at least 3 meters from the zone where you
have refueled before started the machine.
Do not remove the petrol cap whilst the engine is
running.
6.4. CHECK POINTS BEFORE STARTING
Do not use this machine if it becomes damaged or
wrongly regulated.
Use this machine for the purpose for which it was
designed. Any other use may be dangerous for the
user to the machine and for people, animals and
things you may have around.
Verify that :
- The machine completely and look for loose parts
(screws, nuts, etc.) and damages.
- The protector is properly attached to the machine.
- There are not fuel leaks.
- Verify that the disk or head is not damaged.
- Check the air filter is clean. Clean the filter if
necessary.
Press, repair or replace everything you need before
using the machine.
Do not use attachments on this machine out of our
recommendations because their use may cause
serious injury to the user, the machine and the people,
animals and things close to the machine.
Before starting the machine make sure that all moving
parts of the machine are not in contact with any object.
6.4.1. START UP IN COLD
1. Move the air lever (e) to the cold start position.
.
2. Place the switch (a) in the position ¨I¨ (start).
3. Press the primer bulb several times (f) (7 to 10
times) until the fuel reaches the carburetor.
4. Press the security button (b) and after that press
the accelerator trigger (c).
5. Pull the starter rope until you hear the engine start.
6. Move the air lever (e) to the normal
working position.
7. If the engine exploded but did not actally start
running, pull the start rope again until it starts.
Allow the engine to warm up for approximately one
minute before starting to work with the machine.
6.4.1. STARTING THE MACHINE FROM HOT
1. Move the switch (A) to the START position.
2. Move the lever to the
position.
3. Pull the start rope until the machine starts.
If the machine does not start after pulling at the rope a
few times, please refer to the cold start up section.
6.4.2. ENGINE STOPPAGE
1. Let go of the accelerator (C) and let the engine run
at idle speed for a few seconds.
2. Stop the engine by displacing the switch from the
(A) position to the
“0” position (stoppage).
A
B
C
E
D
Содержание XTRIM 900 PG
