manualshive.com logo in svg

Garland STARFIRE SENTRY STW286, Инструкция по установке и обслуживанию

Поделиться
Скачать
Garland STARFIRE SENTRY STW286 Скачать руководство пользователя страница 9

P151 Rev. 1 (03/05)

Page 9

INSTALLATION continued

Commissioning:

The whole of the gas installation, including the meter, 

should be inspected, purged and tested for leakage in 

accordance with local codes.
1.  Ensure that all controls are in the off position and 

turn on the main gas supply and electrical mains. 

2.  Remove  the  screws  securing  the  front  fascia  and 

connect a U-gauge manometer to the pressure test 

point  on  the  main  manifold.  Operate  the  main 

burners in accordance with the instructions given 

in the User’s manual.

3.  Check  that  the  setting  pressure  is  correct  per 

TABLE C on the previous page. If necessary, adjust 

the  pressure  governor  located  at  the  rear  of  the 

range, downstream of the shut-off valve, to give the 

required setting.

Burner Adjustments:

Griddle /Solid Hot Top Burner

Check that the aeration shutter is set to provide the 

required opening per table E on the previous page. Adjust 

if necessary.

FIXING SCREW

SHUTTER

OPENING

MEASUREMENT

INJECTOR
LOCATION

Hot Top Minimum Flame Setting

1.  Set the gas tap to the LOW position. 
2.  Connect a U-gauge manometer to the pressure test 

nipple located downstream of the gas tap.

3.  With  a  flat  screwdriver,  turn  the  adjuster  on  the 

body of the tap clockwise to reduce the pressure or 

anti-clockwise to increase pressure. Set the pressure 

to correspond with table D.

TEST POINT

LOW FLAME
ADJUSTER

PILOT
ADJUSTER

Oven Burner

1.  Check that the aeration shutter is set to the required 

opening per table E. Adjust if necessary.

SHUTTER

OPENING

MEASUREMENT

When all the settings have been checked, remove the U-

gauge manometer, replace the pressure test point screw 

and the lower front panel.
Hand the USER’s INSTRUCTIONS to the user or 

purchaser for retention and instruct them in the efficient 

and safe operation of the appliance.
Tell the user of the location of the gas isolation cock for 

use in an emergency. Leave this Installation and Servicing 

Instruction Manual with the user or purchaser.

Содержание STARFIRE SENTRY STW286





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды