Garland STARFIRE SENTRY STW286 Скачать руководство пользователя страница 4

Страница: 4 / 20

P151 Rev. 1 (03/05)

Page 4

GENERAL INFORMATION

Unpacking:

1. Check crate for possible damage sustained during

transit. Carefully remove unit from crate and again

check for damage. Any damage to the appliance

must be reported to the carrier immediately.

2. The wires for retaining the burners and other

packing material must be removed from units. Any

protective material covering stainless steel parts

must also be removed.

3. All ranges are shipped from the factory with casters

ﬁtted.

4. The splash back is packed separately.

5. The type of gas and the supply pressure that the

equipment was set up for at the factory is noted on

the data plate and on the packaging. This type of

gas supply must be used.

6. Do not remove permanently aﬃxed labels, warnings

or data plates from the appliance, for this may

invalidate the manufacturer’s warranty.

Serial Plate Location:

All burner input ratings are shown on the name/rating

plate of each range which can be located as follows

behind the lower front kick panel, (located below oven

door). To access, remove two (2) fasteners securing the

panel shut.

EXTERIOR DIMENSIONS

Model

Height

Width

Depth

STW286

46-3/4" (1187mm)

36" (914mm)

40-1/2 (1029mm)

NOTE: Height dimensions speciﬁed with casters ﬁtted.

Oven Interior Dimensions

Entry Clearance

Installation Clearances

Shipping

Weight

Manifold

Inlet Size

Height

Width

Depth

Crated

Uncrated

Sides

Rear

13-12"

(343mm)

26-1/4"

(667mm)

22"

(559mm)

43"

(1105mm)

37-7/8"

(648mm)

(178mm)

(152mm)

584lbs.

(265kg)

3/4" NPT

Female

Input Ratings

Operating Pressure

Hot Top

Griddle

Oven

Total

Natural

Propane

BTU

"WC

mbar

"WC

mbar

25,000

7.32

50,000

14.65

30.000

8.79

105,000

30.76

4.5

Model

Description

STW286

36" wide x 46.75" high range with convection over, 12" hot top and 24" griddle section

DIMENSIONS & SPECIFICATIONS

SUFFIX DEFINITIONS
STW 286

286 - 36" wide range with 12" solid hot hot section & 24" griddle
STW - Starfire Sentry range series

Содержание STARFIRE SENTRY STW286





















Результаты поиска

Содержание STARFIRE SENTRY STW286

Отзывы:

Бренды по названию

Популярные бренды

Garland STARFIRE SENTRY STW286, Инструкция по установке и обслуживанию

Результаты поиска

Содержание STARFIRE SENTRY STW286

Отзывы:

Бренды по названию

Популярные бренды