Garland G Series Скачать руководство пользователя страница 30

Страница: 30 / 108

Part # GCTRM Rev 3 (12/10/09)

Page 30

5. To shut the pilot completely off, extinguish the pilot

flame. The internal pilot valve will automatically close

within 60 seconds. Each time this is done, the pilot will

have to be re-lit.

NOTE: This procedure is the same for the convection models

with SIT controls.

Range Base Convection Ovens “RC”

This section pertains to the forced air unit .

For 115 V usage, a cord and plug are provided but

connection to the electrical service must comply with local

codes; or in the absence of local codes, with the National

Electrical Code, ANS/NFPA No. 70-(current edition).

A wiring diagram is attached to the rear of this unit for your

use.

Lighting Instructions

1. Use the access though the louver panel, hold the reset

button (RED) located on the oven safety valve.

2. Using the access hole located below the louver in the

panel, push the RED IGNITOR BUTTON continuously

until the oven pilot ignites.

3. If the pilot does not stay lit after you release the reset

button, wait 5 minutes and repeat Step 2 and hold the

reset button approximately 60 seconds.

PILOT

IGNITOR

BUTTON

REST

BUTTON

ON SAFETY

Lighting Instructions

1. Use the access though the louver panel, hold the reset

button (RED) location on the oven safety valve. (See prior).

2. Using the access hole located below the louver in the

panel, push the RED IGNITOR BUTTON continuously

until the oven pilot ignites. (See Prior)

3 If the pilot does not stay lit after you release the reset

button, wait 5 minutes and repeat Step 2 and hold the

reset button approximately 60 seconds.

Start Up .

1 Activate the power switch to the cook position.

2. Turn the oven valve on. Turn the thermostat to the

desired setting.

Cool Down

1. Turn the thermostat and oven valve off.

2. Open the door.

3. Activate the power to the cool down position.

Shut down

1 Turn the thermostat off.

2. Return the power switch to the “OFF” position.

3. Turn the oven valve off

The motor on the range convection oven is maintenance free

since it is constructed with sealed ball bearings. It is designed

to provide durable service when treated with ordinary care.

We have a few suggestions to follow on the care of your

motor.

Never

operate the oven without convection oven fan.

Use of this oven without the convection fan will cause

premature motor failure!

B. When the motor is operating, it cools itself internally by

air entering the rear of the motor case, provided proper

clearance has been allowed.

C. Since the blower wheel is in the oven cavity, it is at the

same temperature as the oven. If the motor is stopped

while the oven is hot, the heat from the blower wheel is

conducted down the shaft and into the armature of the

motor. This action could shorten motor life.

D. We recommend that at the end of the bake or roasting

period, when the oven will be idle for any period of time,

or before shutting down completely, that the doors

be left open, and by use of the cool-down position on

the fan switch, the fan continues to run for at least 20

minutes. The “FAN” should never be turned “OFF” when

the oven is “HOT”.

Содержание G Series













































































































Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды

Garland G Series, Техническое справочное руководство

Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды