![background image](http://html.mh-extra.com/html/garland/bulk-first-e/bulk-first-e_instruction-manual_3593366042.webp)
English
42/144
English
43/144
To cut a branch, in this case, cut 1/4 of the way on
the side where the branch has the tension and after
that cut the rest of the branch from the other side
(see diagram). This way you will avoid that the branch
tension closes the cut and/or blocks the chain and bar
of the machine.
7.3.4. CUTTING THE BRANCH FROM A TREE
To cut a branch from a tree that is not touching the
ground cut a quarter of the way from the bottom side
(1) and then cut the rest from the top end (2).
This way you will help the
aperture of the cut and that
the branch does not pull and
damage the tree trunk.
7.3.5. BRANCH CUTTING OR SMALL TRUNK CUTTING
When cutting branches or small
trunks use a strong support such
as an easel.
Never hold the trunk by using your
feet or asking someone else to hold the wood for you.
8. MAINTENANCE AND SERVICE
The removal of security mechanisms, an
inappropriate maintenance, the substitution of the
bar and chain with non original spares could cause
severe corporal damages.
Always carry out maintenance work with
the machine unplugged from the mains.
Carry out the following maintenance checks prior to
working as well as when finishing your job to ensure
the good functioning of this machine in the future.
8.1. EXIT ORIFICE OF THE CHAIN OIL
Dismount the bar and check
that the oil orifice (A) is not
clogged.
8.2. SHARPNESS OF CHAIN TEETH
Attention!: An incorrectly sharpened chain increases
the risk of kick back as well as increasing the vibration
level and possible accidents!
To ensure that the machine cuts correctly, maintain
the chain sharpened. You must also sharpen the chain
if:
• You must place more pressure to cut.
• The cut is not straight.
• There is an increase of the vibration levels.
• When cutting instead of splinters you see shavings.
Do not forget to always use security gloves when
sharpening the chain. Make sure the chain is placed
correctly once it has been sharpened.
Use a special file for chainsaws when sharpening the
chain. Place the file between points (a) and (b) and
push the file forward maintaining a 30 angle.
File all the teeth of the chain in the same manner,
filing forward at a 30 angle.
Содержание BULK FIRST E
