Gardner Denver Reavell 5236 Скачать руководство пользователя страница 107

Страница: 107 / 134

APP 090D THERMOMETER SWITCHES

Page 2

CONTROLLER

PART No

TRIP POINTER

STOP SETTING °C

USED ON

COMPRESSOR MODEL

C202960.3

WATER OUTLET

C202960.4

5207,5209,5213

C202960.5

5417N,5436N

C202964.1

5280,5281,5282,5283, DELY

C202964.2

5450,5470 DELY

CONTROLLER

PART No

TEMPERATURE RANGE

°C

USED ON

COMPRESSOR MODEL

98288.1089

50 – 250

°C

,1M

WATER-COOLED 5000 SERIES

98288.1121

0 - 120

°C

, 1M

WATER-COOLED 5000 SERIES

98288.1222

50 - 250

°C

, 5.5M

WATER-COOLED 5000 SERIES

98288.1315

50 - 250

°C

, 5.5M (Russian)

WATER-COOLED 5000 SERIES

98288.1223

0 - 120

°C

, 5.5M

WATER-COOLED 5000 SERIES

98288.1314

50 - 250

°C

, 5.5M (Russian)

WATER-COOLED 5000 SERIES

98288.1298

50-250

°C

,8.5M

WATER-COOLED 5000 SERIES

CONTROLLER

PART No

WHERE FITTED

USED ON

COMPRESSOR MODEL

98288.1093

1st – 5th STG. DELIVERY

5450 & 5470

98288.1094

FINAL DELIVERY

5450 & 5470

•

TO SET TRIP INDICATOR POINTER – FOR PART 98288.1215

The purpose of this switch is to prevent the compressor from starting in lower than recommended ambient

temperatures.it is fitted at the compressor gas inlet port. The minimum temperature of -10°c has been set at

the factory, but this can be raised on site if required by following the procedure below.

To set.

Release adjusting key (A) from back of instrument by removing securing nut.

Insert end of key into central adjuster knob (B) and turn to adjust set pointer to required minimum

temperature

above -10°c.

Replace adjusting key and secure with nut.

CONTROLLER

PART No

TEMPERATURE

RANGE

TRIP POINTER

STOP SETTING °C

USED ON

COMPRESSOR MODEL

98288.1215

-40° / +80°C

-10°C FALLING

5000 SERIES WATER-COOLED

98288.1216

-40° / +80°C

-10°C FALLING

5000 SERIES WATER-COOLED

TYPICAL

SWITCH DIAL

Содержание Reavell 5236







































































































































Результаты поиска

Содержание Reavell 5236

Отзывы:

Бренды по названию

Популярные бренды

Gardner Denver Reavell 5236, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Reavell 5236

Отзывы:

Бренды по названию

Популярные бренды