background image

13-11-607    Page 49

RO membrane

The operational live of the RO membrane also varies with the quality of the raw feed water.  As a general
rule, it should be replaced every 1-2 years.  Typical signs that the device is plugging up are a decrease of
clean water flow and a decrease of rejection of levels of compounds found in the site water.  If rejection of
any compound falls below a 70% level consistently, the membrane should be replaced and so should the
sedimentation and carbon cartridges.

Whenever the rejection levels start decreasing below their minimum acceptable value, a fast-flush valve
(ll) is provided to temporarily increase the internal cleansing of the membrane and hopefully restore
membrane performance.  If the fast-flushing procedure does not restore the rejection performance, than
the membrane must be replaced.

Replacing the RO membrane:

 

Turn off the valve (ff) feeding raw water to the RO system.

 

Open the raw and RO water test drains (gg, qq) to depressurize the water charge from the 
reservoir (nn) and lines.

 

Disconnect the processed water line from the RO housing end cap via the quick disconnect 
fitting.

 

Unscrew the end cap from the housing – reasonable force may have to be used.

 

Remove the used membrane and discard.

 

Lubricate two end o-rings with a coating of clean petroleum jelly.

 

Install the new membrane into housing with two o-rings end first.

 

Lubricate o-rings on membrane housing with a coating of clean petroleum jelly.

 

Thread the cap back on hand-tighten firmly.

 

Close the raw water test point.

 

Open the raw water shutoff valve.  After a minute or so, a trickle of water should be coming 
from the open RO water test drain, indicating the system is again producing water.  Close 
now the RO water test drain.

 

The water reservoir, at a minimum raw water pressure of 50 psig, will fill up in about 2 hours.

Содержание PUREAIR EWC99C






































































Отзывы: