13-20-600 Page 61
10. Replace the O-Ring, Item 5, Figure 5 6, page 61, between the minimum pressure/check valve and
the air/oil separator housing.
11. Replace the sealing kit in the minimum pressure/check valve. After the assembling of the valve,
leave about .08 inch gap between the nut, Item 6, Figure 5-1, page 61, and the cover of the valve.
See “Changing Minimum Pressure/Check Valve Seals,” Section 4, page 28.
12. Install the minimum pressure/check valve assembly and tighten the bolts alternately for even
tightness.
13. Open the air service valve.
14. Run the unit and check for leaks.
COMPRESSOR OIL SYSTEM CHECK
- The following readings are based on ambient temperature of
80
°
F (27
°
C) with the system in good condition. The compressor should be at operating temperature at
the time of the checks. One-half hour of loaded operation is usually sufficient to reach level-out operating
temperatures.
Air and Oil Discharge Temperature
- 160
°
F to 180
°
F (71
°
C to 82
°
C) - Check with a thermometer at
the discharge housing.
Compressor Oil Inlet Temperature
- 150
°
F to 165
°
F (66
°
C to 74
°
C) - Install a tee at the oil filter outlet
and check with a thermometer.
Oil Inlet Pressure
- Check at the fitting in the line near the compressor oil inlet. With air receiver
pressure at 100 psi (6.9 Bar), oil inlet pressure should be 80 to 90 psig (5.5 to 6.2 Bar).
Oil Cooler Oil Pressure Differential (Air-Cooled Radiator)
- Check differential across the oil system by
measuring oil inlet pressure as described above.
Oil Cooler Temperature Differential (Air-Cooled Radiator)
- The oil temperature differential depends
on the temperature of the air at the oil cooler fan and cleanliness of the core faces. As ambient
temperatures and core restrictions increase, the oil cooler outlet temperature will increase. The oil inlet
temperature is approximately the same as the air discharge temperature.
Figure 5 6 – OIL SEPARATOR
Ref.
No. Description
1
Minimum Pressure/Check Valve
2 Air/Oil
Separator
Element
3
Oil Scavenge Line Orifices
4
Oil Scavenge Line Strainer
5 O-Ring
6
Minimum Pressure/Check Valve
Adjusting Nut
Содержание INTEGRA AIRSMART EFC99J
