Gardner Denver APEXVS7-11A Скачать руководство пользователя страница 61

Страница: 61 / 71

13-25-603 Page 60

REPLACING THE AIREND SHEAVE

20. Disconnect, tagout and lockout the power supply to the starter

21. Remove the enclosure panel under the control box.

22. Remove the fan guard and fan orifice.

23. Remove side door panel.

24. Loosen bolts holding airend to support, then loosen nut on jackbolts so that airend lowers, loosening

the belts.

25. Remove the belts.

26. Remove the 2 screws in the airend bushing/sheave assembly and insert one in the jackbolt hole

(Figure 7-2).

Figure 7-1 – REMOVING THE MOTOR SHEAVE

27.

Tighten the screw until the drive bushing and sheave are loose. They can be removed from the
airend shaft by hand, when loosened.

28. When installing a new airend sheave and bushing, remove all protective grease from the bushing

and sheave. Install the bushing into the sheave and align the holes (Figure 7-3).

29. Grease the mounting screws and lightly tighten them. The position of the mounting screws is shown

in Figure 7-3, page 61 the threads are in the sheave only.

Figure 7-2 – INSTALLING BUSHING IN DRIVE SHEAVE

Содержание APEXVS7-11A








































































Результаты поиска

Содержание APEXVS7-11A

Отзывы:

Похожие инструкции для APEXVS7-11A

Бренды по названию

Популярные бренды

Gardner Denver APEXVS7-11A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание APEXVS7-11A

Отзывы:

Похожие инструкции для APEXVS7-11A

Бренды по названию

Популярные бренды