background image

 

13-25-607    Page 19 

 

 

Failure to properly ground the compressor package could result in controller 
malfunction. 

 
7. 

V-Belt System

 - Refer to Section 8 page 50 for detailed instruction to unpack and check the 

alignment of the belt system. 

 

 

 

 

The motor jacking hardware must be re-configured, the disposable spacer 
removed, and belts engaged and the belt sheaves alignment checked prior to 
compressor operation.  Failure to do so will prevent compressor operation and/or 
component damage. 

 
8. 

Rotation

 - Check for correct motor rotation by jogging the motor.  See 

“Maintenance, Motor Jog” 

menu in Controller Operating and Service Manual.  Compressor drive shaft rotation must be 
counterclockwise, standing facing the compressor sheave. 

 

 

 

Operation with incorrect motor rotation can damage equipment and cause oil 
eruption from the compressor inlet.  When checking motor rotation, induce 
minimum rotation (less than one revolution if possible).  Never allow motor to 
reach full speed. 

 

 

 

The compressor unit’s direction of rotation must be checked every time the 
compressor package or its main motor is reconnected to the power supply. 

 

N

N

N

O

O

O

T

TT

I

II

C

C

C

E

E

E

 

  

 

Read the Controller Operating and Service Manual before operating the 
compressor. 

 
9. 

Unload Pressure - 

This is the package discharge pressure beyond which the controller will initiate 

an unload action.  It is set at the factory, but may be changed as desired.  DO NOT EXCEED THE 
MAXIMUM OPERATING PRESSURE ON THE COMPRESSOR NAMEPLATE. See "Operational 
Settings" menu in Controller Operating and Service Manual. 

 
10. 

Load Pressure

 - This is the package discharge pressure at which the controller will halt the unload 

action and load the compressor.  It is typically selected 15psig below the Unload setting.  See 
"Operational Settings" menu in Controller Operating and Service Manual.

Содержание APEX15-18A







































































Отзывы: