background image

 

ADP 4100 Printer 

With respect to a defect in hardware covered by the warranty, the 
warranty shall continue in effect until the end of the original warranty 
period, or for ninety (90) days after the repair or replacement, 
whichever is later. 

General Warranty Provisions 

Unimark makes no warranty as to the design, capability, capacity or 
suitability of any of its hardware, supplies, or software. 

Software is licensed on an “as is” basis without warranty. Except and 
to the extent expressly provided in this warranty and in lieu of all other 
warranties, there are no warranties, expressed or implied, including, 
but not limited to, any warranties of merchantability or fitness for a 
particular purpose. 

Purchaser shall be solely responsible for the selection, use, efficiency 
and suitability of Unimark’s products. 

Limitation of Liability 

In no event shall Unimark be liable to the purchaser for any indirect, 
special or consequential damages or lost profits arising out of or 
relating to Unimark’s products, or the performance or a breach 
thereof, even if Unimark has been advised of the possibility thereof. 
Unimark’s liability, if any, to the purchaser or to the customer of the 
purchaser hereunder shall in no event exceed the total amounts paid 
to Unimark hereunder by the purchaser for a defective product. 

In no event shall Unimark be liable to the purchaser for any damages 
resulting from or related to any failure or delay of Unimark in the 
delivery or installation of the computer hardware, supplies or software 
or in the performance of any services. 

Some states do not permit the exclusion of incidental or consequential 
damages, and in those states the foregoing limitations may not apply. 
The warranties herein give you specific legal rights, and you may 
have other legal rights which vary from state to state. 

ADP 4100 Printer 

Installation and Operators Manual

, April 2007 

39 

Содержание ADP 4100



















































Отзывы: