Gainscha GA-2408T Series Скачать руководство пользователя страница 77

Страница: 77 / 93

10. Printer Program Upgrade

Gainscha printers support program upgrade, if you need to upgrade, please contact relevant

personnel for upgrade guidance.

1. Printer status upgrade

1.1 Prepare for the upgrade

1. The printer is correctly connected to the computer through USB interface;

2. The printer is normally started and in the ready state;

3. Prepare the printer program file (in .gdac or .gpl format) and program upgrade tool FWTool.

1.2 Start the upgrade

Each version of the printer program is different, this case uses model GA-3406T as an example:

1. Open FWTool and check whether the
corresponding port is correct. Click "Get
Printer Info." to obtain the current printer
information.

2. Click “Open File”

3. When selecting the file, select GDAC or

GPL file, then select the corresponding
upgrade file, and click the lower right
corner to open it.

Note: 200DPI model cannot be upgraded to

4. After the selection is complete,
click “Upgrade” on the lower left
corner to upgrade, and the machine
will automatically restart after the
upgrade is completed (do not power
off or perform other operations during

Содержание GA-2408T Series






























































































Результаты поиска

Содержание GA-2408T Series

Отзывы:

Похожие инструкции для GA-2408T Series

Бренды по названию

Популярные бренды

Gainscha GA-2408T Series, Руководство пользователя

Результаты поиска

Содержание GA-2408T Series

Отзывы:

Похожие инструкции для GA-2408T Series

Бренды по названию

Популярные бренды