GAH Electrastream, Руководство пользователя и инструкция по установке

Страница: 50 / 56

2
Important Health and Safety Information for Installers and Service Engineers
Health and Safety at Work Act 1974
Consumer Protection Act 1987
COSHH Regulations 1988
The following information is given as a requirement of the
above legislation.
Great care is taken by GAH (HEATING PRODUCTS) LIMITED
to ensure that Electrastream systems are designed and
manufactured to meet general safety requirements when
properly used and installed as recommended in this manual.
It is the responsibility of Users and Engineers to ensure that
adequate protective clothing and glasses are worn when
working with the Electrastream system.
SEALS AND INSULATION SEALS AND INSULATION SEALS AND INSULATION SEALS AND INSULATION SEALS AND INSULATION
Insulation and sealing materials are used in the construction
of the Electrastream cylinders. Units are sealed and when
used in the manner for which they are intended the insulating
and sealing materials do not present any known hazard.
However always observe the following recommendations:-
1. Avoid inhalation of fibres or dust, wear face mask.
2. Avoid eye contamination by fibres or dust - wear eye
protection.
3. As far as possible avoid any skin contact with Fibreglass
Insulation, Glass Rope, Mineral Wool, Insulation Pads and
Ceramic Fibre.
PPPPPatent application 01514800.2 atent application 01514800.2 atent application 01514800.2 atent application 01514800.2 atent application 01514800.2
© © © © ©
2010 GAH (HEATING PRODUCTS) L 2010 GAH (HEATING PRODUCTS) L 2010 GAH (HEATING PRODUCTS) L 2010 GAH (HEATING PRODUCTS) L 2010 GAH (HEATING PRODUCTS) LTD. TD. TD. TD. TD.
Electrastr Electrastr Electrastr Electrastr Electrastream is a T eam is a T eam is a T eam is a T eam is a Trademark of GAH (HEATING PRODUCTS) L rademark of GAH (HEATING PRODUCTS) L rademark of GAH (HEATING PRODUCTS) L rademark of GAH (HEATING PRODUCTS) L rademark of GAH (HEATING PRODUCTS) LTD. TD. TD. TD. TD.
Manual by Harber Technical Services Tel/Fax 01263 515444
E-mail:info@harbertech.co.uk www.harbertech.co.uk
GAH (Heating Pr GAH (Heating Pr GAH (Heating Pr GAH (Heating Pr GAH (Heating Products) Ltd. oducts) Ltd. oducts) Ltd. oducts) Ltd. oducts) Ltd.
Building 846
Bentwaters Parks
Rendlesham
Woodbridge
Suffolk IP12 2TW
TTTTTel: el: el: el: el: 01394 421160 01394 421160 01394 421160 01394 421160 01394 421160
Fax: Fax: Fax: Fax: Fax: 01394 421170 01394 421170 01394 421170 01394 421170 01394 421170
email: mail@gah.co.uk
www.gah.co.uk
In pursuance of a policy of constant development, GAH (HEATING PRODUCTS) LIMITED
reserve the right to change Electrastream parts or design without notice, therefore
certain details included in this manual may not be correct at the time of printing. Any
modification and improvements detailed in this manual does not commit GAH to update
any system previously supplied.
Manual Part No. ...................MAN1019
Manual Ref ..........................ES02
Issue ...................................13
Date ....................................25/02/13
GAH (HEATING PRODUCTS) LIMITED will not accept
responsibility for any damage or personal injury caused
by not giving due consideration to the above safety
recommendations.
OTHER MATERIALS OTHER MATERIALS
OTHER MATERIALS OTHER MATERIALS OTHER MATERIALS
SEALANTS, ADHESIVES AND PAINTS
Sealants, Adhesives and Paints are used in the construction of
the Electrastream components. When used in the manner for
which they are intended they do not present any known hazard.
ELECTRIC ELECTRIC ELECTRIC ELECTRIC ELECTRIC
The Cylinder Tri-Core Heater, Pump, Thermostats and Contactor
Box all have electrical supply of 230V (enough to endanger
life).
Always isolate before connection, adjustment, servicing and
repair.
When the Tri-Core Heater cover is removed high power live
electrical terminals are exposed.
ISOLATE THE TRI-CORE HEATER BEFORE REMOVING ITS
COVER.
Earth protection - Earth Continuity Conductors must be fitted
and must comply with IEE Wiring Regulations.
HTS REF GAH ELECTRASTREAM 25/02/13
HEAL HEAL HEAL HEAL HEALTH & SAFETY TH & SAFETY TH & SAFETY TH & SAFETY TH & SAFETY
50
IMPORTANT
The final fill of the heating system
should include the correct dose of a
suitable scale/corrosion inhibitor.
Note
Testing the RCD will not affect the operation
of the Electrastream Control Unit.
The Electrastream system should have a routine service at least once in 12 months.
IMPORTANT Always turn off the heating system and electricity supply to
the Electrastream before removing covers and working on the
Electrastream System - this includes the room thermostat cover.
6-1.1 Service Procedure
1. Confirm with the customer the unit’’s service history and locate Benchmark Logbook.
2. Check cylinder model and serial number is listed in the Benchmark Logbook.
3. Visually inspect cylinder/s and vessels for damage, metal failure and signs of leaks.
4. Visually inspect all Electrastream pipework for damage, metal failure and signs of
leaks.
5. Set control unit to midnight to run self test and check Electrastream control unit for
error messages (see fig. 2-2a).
6. Record mains pressure, system pressure and heating operating pressure.
7. Turn the heating OFF at Electrastream Control Unit.
8. Turn the electrical supply to the Electrastream OFF at the isolating switch.
9. Momentarily open the combination TPR Valve and check that the water drains freely
and safely to and from the tundish.
10. Open combination PRV momentarily and close, valve should shut off. Repeat if
valve sticks. If valve will not shut off replace valve.
11. Open heating TPRV momentarily and close, valve should shut off. Repeat if valve
sticks. If valve will not shut off replace valve.
12. Close the Stop Cock.
13. Open the hot and cold taps, attach a hose to the cylinder drain cocks and empty the
system.
14. Remove tri-core heater, remove limescale and examine the element and seal. Refit
if in good condition.
In hard water areas it is probably better to replace the tri-core heater if heavily
scaled. Fit tri-core heater and seal.
15. Clean and check the in-line strainer in the combination valve - replace if required.
16. Check strainers and operation of mixing valve, see 4-3.10.
17. Close all drain cocks and refill system.
18. Check that no water is passing through the Combination Valve or the Pressure Relief
Valves, this will be evident at the Tundish.
19. Switch on the Electrastream isolator, set timer for midnight then set Control Unit and
room thermostat for heat.
20. Wait for the system to self check and heat up.
21. Check temperature of hot tap water, adjust as required, max. 60°C.
22. Check for leaks and bleed system again when the system is up to temperature.
23. Check operation of room thermostat and timer.
24. Check the RCD operation.
25. Enter details of service into the Benchmark Logbook.
6-1 Routine Service
Note
If heavy scaling is evident then descaling
the system is recommended. Ensure
system is fully flushed following descaling.
IMPORTANT
Also carry out any service
requirements of specific
components as specified by the
manufacturers instructions.
SERVICING 6 SERVICING 6 SERVICING 6 SERVICING 6 SERVICING 6
66666