![background image](http://html1.mh-extra.com/html/gage-bilt/gb751srvt/gb751srvt_original-instructions-manual_3223632012.webp)
12
5/17 REV. 1/23
GB751SRVT
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
1.
Ensure lever assembly (724017) is removed from manifold
-
head assembly (744306).
Stand handle assembly (704132) on floor,
stretch tool hoses and head cylinder assembly (703124) upward and lay flat on a table or bench. When bleeding tool always keep
the head cylinder assembly (703124) higher than the handle assembly (704132).
2.
Remove Button Head Cap Screw (402482) and Stat
-
o
-
seal (S572) from manifold
-
handle (744303) hole marked #3. Attach air bleeder
assembly (704153) to manifold
-
handle (744303) hole marked #3 in an upright position.
3.
Connect the tool to air supply and cycle tool ten times holding the actuator assembly
-
air (704130) down for 2
-
3 seconds
between cycles to remove any air from the tool.
4.
Disconnect air supply. Remove air bleeder assembly (704153) from manifold
-
handle (744303) and replace with button head cap
screw (402482) and stat
-
o
-
seal (S572) and torque 35
-
40 inch lbs. (3.95
-
4.52 Nm) Do not over tighten.
5. Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from hole marked #4 on manifold
-
head assembly (744306) and
attach air bleeder assembly (704153) in an upright position.
6.
Connect air supply. Cycle tool ten times removing any air bubbles.
7.
Disconnect air supply. Remove air bleeder assembly (704153) and replace button head cap screw (402482) and stat
-
o
-
seal (S572)
on manifold
-
head assembly (744306) and torque 35
-
40 inch lbs. (3.95
-
4.52 Nm) Do not over tighten.
8.
Connect air supply. Cycle tool ten times and check stroke of
.780” (19.8
mm) using instructions a thru c and diagrams below.
We recommend using dial calipers.
a. With the actuator assembly
-
air (704130) released, check dimension (A).
b. Holding actuator assembly
-
air (704130), check dimension (B).
c. Subtract dim
“
A
”
from dim
“
B
”.
If stroke is not consistent within 1/64" (.396 mm) repeat bleeding steps 5
-
6.
For your consideration, Gage Bilt offers a depth gage (Pt.# A
-
1935) to help simplify and more accurately check your tool stroke.
Please contact Gage Bilt for more information.
9.
Re
-
attach lever assembly (724017) to manifold
-
head assembly (744306).
BLEEDING PROCEDURE:
Images may not reflect actual tool.
WARNING:
Do not cycle tool without air bleeder assembly (704153), or the screw and stat
-
o
-
seal, installed in tool head. Severe
personal injury could result.
WARNING:
Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle assembly (745263). Hydraulic oil may
be under pressure.
CAUTION:
Before filling handle assembly, air piston assembly should be all the way down.
CAUTION:
When forcing piston rod assembly downward, with head cylinder assembly removed, hydraulic oil will eject forcibly from
handle assembly.
CAUTION:
When bleeding tool, ensure tubing is free from kinks or other obstructions.
Note:
•
Air Bleeder Assembly (704153) (sold separately) is required.
* FILLING & BLEEDING VIDEO AVAILABLE AT:
http://www.gagebilt.com/rivet_tools_videos.php
Hole marked #3 on Manifold
Handle (744303)
Air Bleeder
Assembly
(704153)