FXA FXALD1802, Инструкция по эксплуатации

Страница: 11 / 96

11
To fit a keyed drill chuck (not supplied), turn the chuck
and push it in until it engages.
Insert a chuck key (not supplied) into one of the holes
on the keyed drill chuck and then turn the key
anticlockwise until the tool socket is opened wide
enough to insert the drill bit.
Insert the drill bit all the way to the stop.
Insert the chuck key into one of the holes on the
keyed drill chuck and then turn the chuck key
clockwise until the drill bit is securely fastened and
centred in the keyed drill chuck.
Warning! After short operation, switch the product off,
disconnect it from the battery and check once again
that the drill bit is properly fastened. Caution, the drill
bit could be hot.
REMOVING
Insert the chuck key into one of the holes on the
keyed drill chuck and then turn the chuck key
anticlockwise until the tool socket is opened wide
enough to pull out the drill bit.
DEPTH STOP
The depth gauge is convenient for drilling holes of
uniform depth. Push down the depth stop locking
button enough to allow the depth stop to be inserted
through the locating hole Fig.7.
Align the tip of the depth stop with the drill tip. Now
pull the depth stop back by the required drilling depth.
Release the depth stop locking button to fix the depth
stop in position.
AUXILIARY HANDLE
This drill is supplied with the auxiliary handle fitted, to
adjust the position of the auxiliary handle slacken the
handle by rotating it in an clockwise direction Fig.8.
Adjust the auxiliary handle so that you can hold the
product safely during operation (Fig.9 to 11).
Turn the auxiliary handle anti-clockwise to tighten the
clamp.
Warning! Never operate the product without the
auxiliary handle to avoid accidents and injury. Always
ensure that the auxiliary handle is attached and
secured correctly before operation. The auxiliary
handle provides better control of the product in case
of sudden jams during use when considerable forces
are released.
DRILLING MODES (FIG.12)
Caution:
Tool must come to a complete stop before
activating the mode selector button or damage to the
tool may result.
To select the operating mode, press mode selector
button (f) and turn the mode selector (g) so the arrow
points to the corresponding symbol.
Release the mode selector button and check that the
mode selector switch is locked in place.
Note: The arrow on the mode selector must be aligned
with one of the symbols at all times. There are no
operable positions between the positions.
ROTARY DRILLING MODE
Use rotary drilling mode for wood, metal, and
plastics.
HAMMER DRILL MODE
Use this mode for masonry drilling.
HAMMER ONLY MODE
For light chiseling.
VARIABLE SPEED CONTROL (FIG. 13)
Simply apply light pressure to the trigger to start the
drill on a slow speed. Increasing the pressure on the
switch will increase the speed of the drill.
Note: You might hear a high pitched noise from the
switch during use. Do not be concerned; this is a
normal part of the switch function.
FORWARD & REVERSE SWITCH
This feature is selected via a slide switch located
above the trigger, Fig.14. To select direction of the
drill rotation simply push the button fully in on the left
side for reverse rotation. To change to forward
rotation push the button fully in on the right side of the
handle.
Note: As a safety precaution from accidental
engagement while being carried pushing the
forward/reverse button into the middle or neutral
position will render the drill inoperative.
Caution: To prevent gear damage, always allow the
chuck to come to a complete stop before changing
the direction of rotation.
Note: The drill will not run unless the direction of
rotation selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended
periods of time. Running at low speeds under
constant usage may cause the drill to become
overheated. If this occurs, cool the drill by running it
without a load and at full speed.
LED WORK LIGHT
Caution: Do not look in the light or see the source of
light directly.
Pull the On/Off trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being
pulled. The lamp goes out immediately after releasing
the trigger.
GENERAL OPERATION
Check the product, its battery and charger as well as
accessories for damage before each use. Do not use
the product if it is damaged or shows wear.
Double check that accessories or drill bits are properly
fixed.