Futtura MCB1 Скачать руководство пользователя страница 29

Страница: 29 / 33

Automatic Control

APPENDIX I

Self Diagnosing Fault Codes

When the Control Box recognizes a fault, all receiver LED's will light solid and the Power, Auto

and Manual LED’s on the control box will alternately blink.

A speciﬁ c fault information number will be displayed on the LED counter as described in

Appendix D.

1. Switched Power Driver

Description

: Over current (>5A)

Location: Connector

– 10 socket

Pin

– C

Notes

: Driver will shut off for 250ms. It will then retry. If 3 failed tries in 2 seconds, driver stays off until power

is cycled.

Possible External Causes:

Short in cable coil or connectors.

2. Load Sense Driver

Description

: Over current (>5A)

Location: Connector

– 10 socket

Pin

– D

Notes

: Driver will shut off for 250ms. It will then retry. If 3 failed tries in 2 seconds, driver stays off until power

is cycled.

Possible External Causes:

Short in cable coil or connectors.

3. Auxiliary Driver 2

Auxiliary Driver 2

Description

: Over current (>5A)

Location: Connector

– 10 socket

Pin

– F

Notes

: Driver will shut off for 250ms. It will then retry. If 3 failed tries in 2 seconds, driver stays off until power

is cycled.

Possible External Causes:

Short in cable coil or connectors.

4. Auxiliary Driver 3

Auxiliary Driver 3

Description

: Over current (>5A)

Location: Connector

– 10 socket

Pin

– G

Notes

: Driver will shut off for 250ms. It will then retry. If 3 failed tries in 2 seconds, driver stays off until power

is cycled.

Possible External Causes:

Short in cable coil or connectors.

5. Raise Proportional Current (PC) & Proportional Time (PT) Driver

Raise Proportional Current (PC) & Proportional Time (PT) Driver

Description

: Over current (>5A)

Location: Connector

– 10 socket

Pin

– B

Notes

: Driver will shut off for 250ms. It will then retry. If 3 failed tries in 2 seconds, driver stays off until power

is cycled.

Possible External Causes:

Short in cable coil or connectors.

6. Lower Proportional

Lower Proportional Current (PC) & Proportional Time (PT)

(PC) & Proportional Time (PT) Driver

Description

: Over current (>5A)

Location: Connector

– 10 socket

Pin

– A

Notes

: Driver will shut off for 250ms. It will then retry. If 3 failed tries in 2 seconds, driver stays off until power

is cycled.

Possible External Causes:

Short in cable coil or connectors.

Содержание MCB1


































Результаты поиска

Содержание MCB1

Отзывы:

Похожие инструкции для MCB1

Бренды по названию

Популярные бренды

Futtura MCB1, Инструкция по установке/Техническая информация

Результаты поиска

Содержание MCB1

Отзывы:

Похожие инструкции для MCB1

Бренды по названию

Популярные бренды