FUTABA FDP02TJ010 Скачать руководство пользователя страница 57

Страница: 57 / 67

Ver.1.1

9. Interface

9.1 Pin Layout

Pin No.

Pin name

Input/output

Remark

1 Vcc

－

Power supply (3.3 to 5.5 VDC)

2 RXD

OUT

Data output

3 TXD

Data input

CTS

OUT

Hardware flow control

RTS

Hardware flow control

6 TES

－

(Leave this pin unconnected.)

7 /INI

Parameter initialization

8 /SHUT

Power-off

9 TES

－

(Leave this pin unconnected.)

10 GND

－

Ground

Explanation of the pins

Vcc: Power supply pin. Connect a power source and the voltage range is from 2.5 to 5.5 VDC.

RXD: Data output pin that is the DCE compliant

TXD: Data input pin that is the DCE compliant

CTS: Hardware flow control output pin that is the DCE compliant (Hardware flow control is enabled

when the signal is high level.)

RTS: Hardware flow control input pin that is the DCE compliant (Hardware flow control is enabled

when the signal is high level.)

/INI: Parameter initialization pin. Leave this pin unconnected when it is not used. To initialize the

registers, set the /INI pin to low level at power-on or combine the operation of this pin with the

operation of the /SHUT pin. After the registers (parameters) are initialized, the DP01 operates in

normal mode.

/SHUT: Power-off pin. When this pin is set to low level, the main power of the FDP02 is cut and becomes

“power-down” mode. When the setting of this pin is high level, the FDP02 is in normal operation

mode.

TEST: Test pin. Do NOT use this pin. This pin is only for maintenance by the manufacturer.

GND: Ground pin

Parameter setting of the register will be vanished if the /SHUT pin

becomes low level and the operation mode becomes “power-down”

mode. Therefore, DO NOT connect /SHUT pin during REG

command setting.

After releasing from the power-down mode, parameter settings of

registers that were changed by commands will be initialized. Thus,

the parameter settings should be done by the memory registers when

the “power-down” mode is used or set the parameters again after

returning from the “power-down” mode.

It will take 90 ms at the maximum to return from the “power-down”

mode to normal operation mode.

9.2 Recommended Connector

Hirose Electric Co., Ltd. DF12E(3.0)-10DP-0.5V

Содержание FDP02TJ010




































































Результаты поиска

Содержание FDP02TJ010

Отзывы:

Похожие инструкции для FDP02TJ010

Бренды по названию

Популярные бренды

FUTABA FDP02TJ010, Инструкция по эксплуатации

Результаты поиска

Содержание FDP02TJ010

Отзывы:

Похожие инструкции для FDP02TJ010

Бренды по названию

Популярные бренды