90
＜
Linkage Menu
＞
HELI
COPTER
AIRPLANE
GLIDER
●Return to Linkage Menu
● Touch the [Fail Safe] button in the Linkage Menu to
call the setup screen shown below.
Fail Safe
Sets the servos operating position when transmitter signals
can no longer be received or when the receiver battery
voltage drops.
(The display screen is an example. The screen depends on the model type.)
The Failsafe function is used to set up positions that the
servos will move to in the case of radio interference.
Defines servo position when signals are lost and when
receiver battery voltage becomes low.
You may set either of two positions for each channel:
Hold, where the servo maintains its last commanded
position, or fail safe, where each servo moves to a
predetermined position. You may choose either mode for
each channel.
The T32MZ system also provides you with an advanced
battery monitoring function that warns you when the
receiver battery has only a little power remaining. In this
case, each servo is moved to the deined failsafe position.
The battery failsafe may be released by operating a
predeined control on the transmitter (default is throttle).
Do not continue to fly, land as soon as possible.
Remember, if the predeined control suddenly moves to
Fail safe setting procedure
Decide which channels you want to go to preset
positions, and which ones you want to maintain their
last commanded position. To select the fail safe mode
you wish to set, use the F/S button. This button toggles
between the two modes. (Hold, F/S)
F/S mode setting:
1. Touch the F/S button of the channel you want to
set, and set that channel to the [F/S] mode.
2. Hold the corresponding stick, control, slider, or
other control in the position you want the servo to
move to when the fail safe function is activated,
and touch the F/S position button. That position is
displayed in percentage.
*When you want to return that channel to the Hold
mode, touch the [F/S] button again.
Battery fail safe setting procedure
To select the B.F/S mode, touch the [B.F/S] button. Each
time the button is touched, it toggles between [OFF] and
[B.F/S].
a position you did not command, land at once and check
your receiver battery.
Do not continue to fly, land as soon as possible.
Defines servo position when signals are lost and when
receiver battery voltage becomes low.
WARNING
For safety, always set the fail safe functions.
■
Especially set the throttle channel fail safe function so that
the servo moves to the maximum slow side for airplanes and
to the slow side from the hovering position for helicopters.
Crashing of the model at full high when normal radio
waves cannot be received due to interference, etc., is very
dangerous.
■
If fail safe is reset by throttle stick movement, the fail safe
may be mistaken as an engine malfunction and will be reset
at low throttle and the model will continue to ly. If you have
any doubts, immediately land.
B.F/S setting:
1. Touch the [B.F/S] button of the desired channel to
set it to the B.F/S mode.
2. Hold the corresponding stick, VR, slider, or other
control in the position you want the servo to move
to when the battery fail safe function is activated,
and touch the F/S position button. This position is
displayed in percentage.
*When you want to return that channel to OFF,
touch the [B.F/S] button again.
Battery Fail safe Release Function
This function releases the predefined control from it's
held position after indicating that your receiver battery is
low.
1. Enter the control setting screen by touching the
Battery F/S Release button. Now, you may choose
whether moving the throttle resets the condition,
or select a stick or switch to deactivate it. To set a
desired throttle release position, move the throttle
stick to the point at which you wish the B.F/S to be
released.
●To <Switch>
screen
Содержание 32MZ
Страница 1: ...1M23Z06801 INSTRUCTION MANUAL...
