background image

ASD-120 SEQUENCED POWER DISTRO

18

Limited Warranty

The Furman ASD-120 is warranted against failures due to defective parts or

faulty workmanship for a period of three years after delivery to the original owner.
During this period, Furman will make any necessary repairs without charge for
parts or labor. Shipping charges to the factory or repair station must be prepaid by
the owner; return shipping charges (via UPS Ground) will be paid by Furman. This
warranty applies only to the original owner and is not transferable. Also, it does not
apply to repairs done other than by the Furman factory or Authorized Repair Sta-
tions. This warranty shall be cancelable by Furman at its sole discretion if the ASD-
120 unit has been subjected to physical abuse or has been modified in any way
without written authorization from Furman. Furman’s liability under this warranty is
limited to repair or replacement of the defective unit. Furman will not be responsible
for incidental or consequential damages resulting from the use or misuse of its
products. Some states do not allow the exclusion of incidental or consequential
damages, so the above limitations may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to
state. Warranty claims should be accompanied by a copy of the original purchase
invoice showing the purchase date (if a Warranty Registration Card was mailed in
at the time of purchase, this is not necessary). Before returning any equipment for
repair, please read the important information on service below.

Service

Before returning any equipment for repair, please be sure that it is adequately

packed and cushioned against damage in shipment, and that it is insured. We
suggest that you save the original packaging and use it to ship the product for
servicing. Also, please enclose a note giving your name, address, phone number
and a description of the problem. NOTE: All equipment being returned for repair
must have a Return Authorization (RA) Number. To get an RA Number, please call
the Furman Service Department, (707) 763-1010, Ext. 40, between 8 am and 5 pm
U.S. Pacific Time. Please display your RA Number prominently on the front of all
packages.

Содержание ASD-120





















Отзывы: