Fukuda Denshi HLX-561 Скачать руководство пользователя страница 4

Страница: 4 / 28

Telemetry Precautions

For proper management of the telemetry installation, consult your
Fukuda Denshi representative concerning the following:

•

Plan the installation of your telemetry system taking into account

your entire medical facility needs and plant requirements.

•

Be sure the antenna system installed meets the facility and plant

requirements.

WARNING

This Radio Frequency device is susceptible to interference
from outside sources. Interference may prevent the
monitoring of patients connected to this device. If problems
exist contact your local service representative.

NOTE :

This device operates in the 600MHz UHF band. The exact

frequency of operation depends on designation, and each
individual county's wireless service regulation.

To assure safe and reliable operation, observe the following
precautions:

•

Be sure that no other devices are using the frequency assigned to this

transmitter.

•

This device is susceptible to interference from electrosurgical knives

and other computerized equipment. If problems occur contact your
local Fukuda Denshi service representative.

•

Any obstruction such as reinforced concrete or large metallic surfaces

between the receiver and the transmitter can affect reception. If
problems occur contact your local Fukuda Denshi service
representative.

•

When the low battery alarm is present at the central monitor, charge

the battery in the patient monitor.

Содержание HLX-561





























Результаты поиска

Содержание HLX-561

Отзывы:

Похожие инструкции для HLX-561

Бренды по названию

Популярные бренды

Fukuda Denshi HLX-561, Руководство по эксплуатации

Результаты поиска

Содержание HLX-561

Отзывы:

Похожие инструкции для HLX-561

Бренды по названию

Популярные бренды