Fujitsu XG2000 Series Скачать руководство пользователя страница 299

Страница: 299 / 315

XG2000 series User's Guide

299/315

A.2.12

ntp (NTP Control: 8600-8699)

Message ID

Severity

Message/Explanation/Solution

P8601
WARNING

No server suitable for synchronization found.

Explanation

No NTP server is found.

Solution

Check the NTP server host name defined by the "ntp-server" command as well as the NTP server operating
status.

P8602
INFO

Time server %1$ offset %2$ sec.

Explanation

Time synchronization using a NTP server was performed to correct the time.

[[Inserted string]]%1$: Host name or IP address of the NTP server that corrected the time

[[Inserted string]]%2$: Corrected time difference in seconds

P8603
WARNING

Cannot find host %1$.

Explanation

Failed to find an IP address from the host name specified with the "ntp-server host" command.

[[Inserted string]]%1$: Host name specified with the "ntp-server host" command

Solution

Review the host name defined.
Check that DNS was configured.

P8691
ERROR

System Error: %1$

Explanation

A system error occurred while NTP time synchronization was in progress.

[[Inserted string]]%1$: Additional information on the error

Solution

Note the message contents and contact the sales representative.

Содержание XG2000 Series

























































































































































































































































































































Результаты поиска

Содержание XG2000 Series

Отзывы:

Fujitsu XG2000 Series, Руководство пользователя, Страница: 299 / 315

Результаты поиска

Содержание XG2000 Series

Отзывы: