Fujitsu XG2000 Series Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 315

Fujitsu XG2000 Series Скачать руководство пользователя страница 143

XG2000 series User's Guide

143/315

All Rights Reserved, Copyright (C) PFU LIMITED 2009

z

Link Status Detail

Details of the port are displayed:

Display

Meaning

PLUG-OUT

The XFP is not installed.

LOW-PWR

The XFP is in low power state.

PHY

Access to the XFP failed.

CLI

The shutdown command was executed.

TMR

Since the shutdown command and link-aggregation command were executed, the port is
down for a certain period of time.

AGG-MIN

The number of ports in a link up state comprising an aggregation group became less than
the minimum number of ports required to maintain a link up state.

LF

A local fault was detected.

RF

A remote fault was detected.

LPT

A link down state notification through the link pass through function occurred.

SDL

Frame discarding due to broadcast storm control was detected.

PSL

Frame discarding due to a port security violation was detected.

LAL

Frame discarding due to a loop back alert was detected.

SYS

An internal system contradiction was detected.

z

STP

State

−

Disabled

The port is in a state to discard data traffic.

−

Learn

The port is in the learning state. It prepares for forwarding data traffic. It discards
data traffic.

−

Forward

The port is ready to transmit data traffic.

z

Flow

Control

−

Disabled

PAUSE flow control is disabled.

−

Rx

Only

Rx PAUSE flow control is enabled.

−

Tx

Only

Tx PAUSE flow control is enabled.

−

Rx

and

TX

Rx and Tx PAUSE flow control is enabled.

z

Address

Learning

−

Enabled

Dynamic MAC address learning is enabled.

−

Disabled

Dynamic MAC address learning is disabled.

z

Multicast

Forwarding

−

Forward-all

All multicast frames will be forwarded (flooded).

−

Forward-unregistered-mac

Multicast addresses yet to be registered in the static MAC address table, and multicast
addresses registered will be forwarded (flooded).

−

Filter-unregistered-mac

Only Multicast addresses registered in the static MAC address table will be forwarded.

z

Port

Security

−

Shutdown

When a violating frame is detected, the port enters a violation state and goes link
down.

−

Restrict

When a violating frame is detected, the port enters a violation state, and the violating
frame is discarded.

−

Disabled

Port security is disabled.

z

Storm

Control

−

Enabled

Broadcast storm control is enabled.

−

Disabled

Broadcast storm control is disabled.

z

Default Qos Priority

The QoS priority <0-7> is displayed.

z

Qos Egress Scheduling

−

Strict

Forwarding is scheduled using strict priority.

−

DRR

Forwarding is scheduled using round robin.

−

DRR-Strict

Forwarding is scheduled using both strict priority and round robin.

z

Qos

Bandwidth

Bandwidth for each output queue priority is displayed

z

Ingress

Bandwidth

The ingress rate limiting value of the port is displayed in Mbps.

For an aggregation group, the ingress rate limiting value total "(total:<240-60000>)," is
displayed.

«
...
141
142
143
144
145
...
»

Содержание XG2000 Series




























































































































































































































































































































Отзывы:

Нет отзывов