Fujitsu XG2000 Series Скачать руководство пользователя страница 166

Страница: 166 / 315

XG2000 series User's Guide

166/315

5.11.7 spanning-tree port-priority

Function

Sets a port priority within the Spanning Tree.

A smaller value has a higher priority.
Use the no form to return to the default setup.

Prompt

xg(config-if)# or xg(config-agg)#

Command syntax

spanning-tree port-priority <0-240>
no spanning-tree port-priority

Parameter

port-priority

<0-240>

Specifies a port priority value within the Spanning Tree. Specify a value divisible by 16.
It can be within the range of 0 to 240.

Command type

Configuration command

Default

128

Message

% Priority is not step of 16

Explanation

The priority value specified is not an integer divisible by 16.

Solution

Specify a priority value divisible by 16.

Example

Set the priority of port2 to 160.

xg(config)# interface port 2
xg(config-if)# spanning-tree port-priority 160

5.11.8 spanning-tree port-path-cost

Function

Sets a path cost for each port.
Use the no form to return to the default setup.

Prompt

xg(config-if)# or xg(config-agg)#

Command syntax

spanning-tree port-path-cost <1-200000000>
no spanning-tree port-path-cost

Parameter

port-path-cost

<1-200000000>

Sets a path cost for each port. It can be within the range of 1 to 200000000.

The following path cost values are recommended by IEEE802.1D.

IEEE802.1D (16bit)

IEEE802.1D (32bit)

Link speed

Recommended

range

Recommended

value

Recommended

range

Recommended

value

100M bps

10 - 60

20000 - 2000000

200000

1G bps

3 - 10

2000 - 200000

20000

10G bps

1 - 5

200 - 20000

2000

Command type

Configuration command

Configuration command Default

2 (16bit)
2000 (32bit)

Example

Set the path cost for port 2 to 3:

xg(config)# interface port 2
xg(config-if)# spanning-tree port-path-cost 3

Содержание XG2000 Series

























































































































































































































































































































Результаты поиска

Содержание XG2000 Series

Отзывы:

Fujitsu XG2000 Series, Руководство пользователя, Страница: 166 / 315

Результаты поиска

Содержание XG2000 Series

Отзывы: