Fujitsu UTY-RNN*M series, Руководство по установке

Страница: 2 / 10

En-1
INSTALLATION MANUAL
PART NO. 9373328162-04
AIR CONDITIONER REMOTE CONTROLLER
(WIRED TYPE)
Contents
1. SAFETY PRECAUTIONS .............................................. 1
2. ACCESSORIES ............................................................. 1
3. ELECTRICAL REQUIREMENT ...................................... 1
4. SELECTING AN INSTALLATION LOCATION
4.1. Dimensions ............................................................. 2
4.2. Name of parts ......................................................... 2
5. INSTALLING THE REMOTE CONTROLLER
5.1. Installation .................................................................. 3
5.2. Setting the DIP switch ............................................ 3
5.3. Connection of Remote Controller Cable ................. 4
6. INSTALLATION METHODS
6.1. Group control .......................................................... 4
6.2. Dual remote control ................................................ 4
7. TURNING ON THE POWER .......................................... 5
8. SETTING THE ROOM TEMPERATURE
DETECTION LOCATION .................................................. 5
9. FUNCTION SETTING .................................................... 5
10. TEST OPERATION ........................................................ 7
11. ERROR CODES ............................................................ 8
1. SAFETY PRECAUTIONS
Let the customer keep this installation manual because it is needed •
when the air conditioner or remote controller is serviced or moved.
WARNING
This mark indicates procedures which, if improp-
erly performed, might lead to the death or serious
injury of the user.
For the air conditioner to operate satisfactorily, install it as outlined in •
this installation manual.
Installation work must be performed in accordance with national wiring
•
standards by authorized personnel only.
Do not turn on the power until all installation work is complete.
•
CAUTION
This mark indicates procedures which, if improp-
erly performed, might possibly result in personal
harm to the user or damage to property.
When detecting the room temperature using the remote controller, •
please set up the remote controller according to the following
conditions. If the remote controller is not located properly, the correct
room temperature will not be detected, and thus abnormal conditions
like “not cooled” or “not heated” will occur even if the air conditioner is
running normally.
Locate where an average temperature •
for the room being air-conditioned will be
sensed.
Do not locate directly exposed to the outlet
•
air from the air conditioner.
Locate out of direct sunlight.
•
Locate away from the in fl uence of other •
heat sources.
Do not touch the remote controller PC board and •
PC board parts directly with your hands.
Do not wire the remote controller cable and the bus wire together with
•
or parallel to the connection cables, transmission cables, and power
supply cables of the indoor and outdoor units. It may cause erroneous
operation.
When installing the bus wire near a source of electromagnetic waves,
•
use shielded wire.
Do not set the DIP switches, either on the air conditioner or the remote
•
controller, in any way other than indicated in this manual or the manual
that is supplied with the air conditioner. Doing so may result in an
improper operation.
Temperature sensor
2. ACCESSORIES
The following installation parts are supplied. Use them as required.
Name and Shape Q’ty Application
Installation manual
1
This manual
Operating manual
1
Instruction book for operation
Remote controller cable
1
For connecting the remote
controller
Connecting cable
1
For connecting the remote control-
ler cable to the wall mounted type
and the
fl oor type indoor unit
Tapping screw (M4 x 16mm)
2
For installing the remote controller
Binder
1
For remote controller and remote
controller cable binding
Tapping screw (M4 x 14mm)
1
For installing the remote controller
cable to the indoor unit
Cable clamper
1
For installing the remote controller
cable to the indoor unit
3. ELECTRICAL REQUIREMENT
When connecting the remote controller use the following wiring.
Cable Cable size Remarks
Remote controller
cable
22AWG
Sheathed PVC cable,
Polar 3 core
Use Sheathed PVC
cable in accordance with
local rules for cable.
* We recommend that you purchase our service parts for the remote control-
ler cable. Contact service personnel to purchase this.
9373328162-04_IM.indb Sec1:1 9373328162-04_IM.indb Sec1:1 2011-12-5 14:29:24 2011-12-5 14:29:24