manualshive.com logo in svg

Fujitsu SPARC Enterprise T5140, Примечания к продукту, Страница: 62 / 138

Поделиться
Скачать
Fujitsu SPARC Enterprise T5140 Скачать руководство пользователя страница 62

52

SPARC Enterprise T5140 and T5240 Servers Product Notes • November 2012

Incorrect Operating Input Voltage Values for the 1.6 
GHz, 8-Disk Configuration

The table that describes input power requirements for the SPARC Enterprise T5240 server 
configuration with 1.6 GHz CPUs and an 8-disk capable backplane states the wrong 
operating input voltage value in two places. The following table describes the necessary 
correction.

Note – 

The operating input voltage range for the DC input model is correct.

Note – 

The 200 to 240 VAC operating input voltage range is required only for servers 

equipped with 16-disk capable backplanes. All other configurations support the 100 to 240 
VAC operating voltage range.

SPARC Enterprise T5140 and T5240 Servers 

Installation Guide

This manual includes descriptions using the cable management arm (CMA); however, the 
SPARC Enterprise T5140 server doesn't support the cable management arm. 

Verify Proper Seating of Preinstalled PCIe/XAUI 
Cards

The server installation procedure should include instructions for verifying that any 
preinstalled PCIe and/or XAUI cards and their risers have not worked loose during shipping. 
This procedure should also include instructions for verifying that internal cables are properly 
routed and that their connections are secure.

Location of Incorrect Values

Incorrect Value

Correct Value

Table for T5240 Server, 1.6 GHz CPU, 8-disk backplane

Operating input voltage range

200 to 240 VAC

100 to 240 VAC

Maximum operating input current

At 100 VAC: <n/a>

At 100 VAC: 14.0A

Содержание SPARC Enterprise T5140











































































































































Отзывы:

Нет отзывов