Fujitsu PRIMERGY TX300 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 127

Fujitsu PRIMERGY TX300 Скачать руководство пользователя страница 90

84

A26361-K881-Z102-4-7619

Hot-swap Hard Disk Drives

Hot-plug/hot-swap Components

The hard disk drives that can be ordered for the PRIMERGY TX300 are
delivered as HDD modules, with the hard disk drives preinstalled on carriers.
The hard disk drive may only be removed from the carrier by personnel with the
appropriate technical training in compliance with the appropriate ESD guide-
lines (see section “Modules with electrostatic-sensitive components:” on
page 18).

Figure 31: HDD module and dummy module

1

HDD module (hard disk drive carrier with installed hard disk drive)

2

Indicators
HDD busy (LED green
HDD fault (LED orange)
Description see table on page 59 in section „Hard disk drive
indicators“.

3

Handle for locking and unlocking of the hard disk drive module

4

Locking button

5

Ridge for the application of a sticker with the current drive identifier

6

Dummy module

7

Locking tabs

«
...
88
89
90
91
92
...
»

Содержание PRIMERGY TX300
































































































































Отзывы:

Нет отзывов