Fujitsu PRIMERGY TX300 Скачать руководство пользователя страница 80

Страница: 80 / 127

A26361-K881-Z102-4-7619

The Floppy Disk Cannot be Read or Written

Troubleshooting and Tips

Mouse controller disabled

The mouse controller on the system board must be enabled if you use the
supplied mouse.

Check in the

BIOS Setup

that the mouse controller is

Enabled

7.7

The Floppy Disk Cannot be Read or Written

Check whether the write protection for the floppy disk is activated.

Check the entry for the floppy disk drive in the

BIOS Setup

Check in the

BIOS Setup

whether the floppy disk drive controller and write

permission are enabled (see technical manual for system board on the
PRIMERGY ServerBooks CD).

7.8

Incorrect Time and/or Date

Set the time and/or date in the operating system or in

BIOS Setup

If the time and date are repeatedly wrong when you switch on your
server, you must change the lithium battery. Contact our Service group.

7.9

System Fails to Boot

The system will not boot after installing a new hard disk drive.

Incorrect SCSI configuration (Ultra Wide SCSI Controller)

In the SCSI configuration menu check the settings for the hard disk drives
(

SCSI Device Configuration

) and the settings under

Advanced Configuration

Options

Содержание PRIMERGY TX300
































































































































Результаты поиска

Содержание PRIMERGY TX300

Отзывы:

Fujitsu PRIMERGY TX300, Руководство по эксплуатации, Страница: 80 / 127

Результаты поиска

Содержание PRIMERGY TX300

Отзывы: