Fujitsu PRIMERGY TX300 Скачать руководство пользователя страница 78

Страница: 78 / 127

A26361-K881-Z102-4-7619

The Server switches itself OFF

Troubleshooting and Tips

7.2

The Server switches itself OFF

Server Management has detected an error

Check the error list or the ErrorLog file in the

ServerView

program, and

attempt to eliminate the error.

7.3

The Monitor Remains Dark

Monitor is switched OFF

Switch on your monitor.

Screen has gone blank

Press any key on the keyboard.

Deactivate screen blanking (screen saver). Enter the appropriate password.

Brightness control is set to dark

Set the brightness control on the monitor to light. For detailed information,
please refer to the Operating Manual supplied with your monitor.

Power cable or monitor cable not connected

Switch off the monitor and the server.

Check whether the power cable is properly connected to the monitor and to
the grounded socket.

Check whether the monitor cable is properly connected to the server and
monitor (if it is plugged in with a connector). If a separate graphics card is
installed in the server, then the monitor cable must be connected to the
graphics card.

Switch on the monitor and the server.

Содержание PRIMERGY TX300
































































































































Результаты поиска

Содержание PRIMERGY TX300

Отзывы:

Fujitsu PRIMERGY TX300, Руководство по эксплуатации, Страница: 78 / 127

Результаты поиска

Содержание PRIMERGY TX300

Отзывы: