background image

46

Operating Manual

 RX4770 M2

Hardware installation

I

For PRIMECENTER Racks and DataCenter Racks:

The mounting of the rails in the different racks is described in the next 
sections. Installation of the cable management is described in detail in 
the Technical Manual for the respective rack.

I

For 19-inch standard rack (for the Japanese market):

For information on mounting of the rails in the 19-inch standard rack (for 
the Japanese market) please refer to the "Rack system structure guide" 
(refer to 

http://primeserver.fujitsu.com/primergy/peripheral/rack/

).

3rd party racks

Certain general conditions must be met:

– Installation dimensions (see the dimensions shown in 

figure 2 on page 47

): 

1

Front of rack

2

Rear of rack

A

Rack depth (comparison PRIMECENTER Rack 940/1000/1100 mm)

B

Rack width (comparison PRIMECENTER rack 700 mm)

C

Clearance for 19" installation level

C1

Front 19" installation level

C2

Rear 19" installation level

D

Cable routing area (cable area depth) and ventilation

E

Space for front panel and ventilation

F

Space for right and left support systems

P

PRIMERGY rack installation depth

a1

Front left support upright

a2

Front right support upright

b1

Rear left support upright

b2

Rear right support upright

Содержание PRIMERGY RX4770 M2





















































































Отзывы: