C141-E064-03EN
5 - 19
5.
The saved value of the MODE SELECT parameter is assumed as the
initial value of each parameter after the power-on, the RESET
condition, or the BUS DEVICE RESET message. The INIT can
change the parameter value temporary (actively) at any timing by
issuing the MODE SELECT or MODE SELECT EXTENDED
command with specifying "0" to the SP bit in the CDB.
(1)
Error recovery parameter
The following parameters are used to control operations such as IDD internal error recovery:
a. Read/write error recovery parameters (page code = 1)
Parameter
Default value
• ARRE:
• TB:
• EER:
• PER:
• DCR:
Automatic alternate block allocation at read
operation
Uncorrectable data transfer to the INIT
Immediate correction of correctable error
Report of recovered error
Suppression of ECC error correction
1 (enabled)
1 (enabled)
1 (enabled)
0 (disabled)
0 (Correction is
enabled.)
• Retry count at read operation
• Retry count at write operation
• Recovery time limit
63
0
30 sec
b. Verify error recovery parameters (page code = 7)
Parameter
Default value
• ERR:
• PER:
• DTE:
• DCR:
Immediate correction of recoverable error
Report of recovered error
Stop of command processing at successful
error recovery
Suppression of ECC error correction
1 (enabled)
0 (disabled)
0 (Processing is
continued.)
0 (Correction is
enabled.)
• Retry count at verification
63
c. Additional error recovery parameters (page code = 21)
Parameter
Default value
• Retry count at seek error
15
Содержание MAE3091LC SERIES
