Fujitsu IP Centrex SRS-12i Скачать руководство пользователя страница 13

Страница: 13 / 69

2-3

Fujitsu

IP Centr

ex T

elephone

Network Settings

DHCP Setting (Option 13)

DHCP is a Dynamic Host Automatic Configuration Protocol that allows a
server to dynamically assign IP addresses to workstations.

1. Press OPTIONS, numeric key “1”, “3”, then ENTER.

(If NON SUPPORTED was selected previously, the screen will show
“NON SUPPORTED.”)

2. Press ENTER.

3. Enter 4 digits of numeric password (see User Password Registration in

chapter 4).

* Factory Default User Password - 9999

4. Press ENTER.

5. Press 1, then ENTER for support of DHCP. (Or press 2, then ENTER to

deactivate support of DHCP.)

6. Press OPTIONS to exit the option menu. The telephone will reboot

automatically.

When 1: SUPPORT is selected, but the set could not obtain IP address, the
following error message will be shown:

User can manually enter the IP Address by going back to Menu by pressing
OPTIONS while DHCP ERROR message is displayed.

(See IP Address Registration Option 14 in this chapter).

Press either asterisk (*) to go back to sub-menu or OPTIONS to exit the option
menu.

DHCP SETTING
SUPPORTED

ENTER USER PASSWORD

****

1: SUPPORT

2: NO SUPPORT
(SELECT 1-2)

SUPPORTED
COMPLETED

DHCP Outage

Содержание IP Centrex SRS-12i






































































Результаты поиска

Содержание IP Centrex SRS-12i

Отзывы:

Похожие инструкции для IP Centrex SRS-12i

Бренды по названию

Популярные бренды

Fujitsu IP Centrex SRS-12i, Руководство администратора

Результаты поиска

Содержание IP Centrex SRS-12i

Отзывы:

Похожие инструкции для IP Centrex SRS-12i

Бренды по названию

Популярные бренды