Fujitsu Fujitsu fi-5950 Скачать руководство пользователя страница 233 | Manualshive

Страница: 233 / 257

Fujitsu Fujitsu fi-5950 Скачать руководство пользователя страница 233

213

8.21 Auto Color Detection

8

SCANNER SETTINGS

8.21 Auto Color Detection

You can adjust the slice level for auto color detection.

Configure the settings for the Auto Color Detection as follows:

1.

Start up the Software Operation Panel.

“8.1 Scanner Settings” on page 173

.

2.

Select [Device Setting 2] from left side list in the window, and select [Auto
color Detection] from its lower level.

3.

Select the Slice value.

You can select the Slice value from 1 to 255 (255 levels).
In the case that black and white documents are judged as color documents, select larger values.
In the case that color documents are judged as black and white, select smaller values.

HINT

The auto color detection setting can be configured on the scanner driver set-
ting window.
For details on how to set the setting, refer to

“3.11 Color/monochrome Auto

Detection” on page 92

.

«
...
231
232
233
234
235
...
»

Содержание Fujitsu fi-5950


































































































































































































































































Отзывы:

Нет отзывов