Fujitsu eclipse Скачать руководство пользователя страница 45

Страница: 45 / 76

MDE-3893P Encore® and Eclipse® Series Owner’s Manual · December 2011

Page 41

Periodic Inspections

Maintaining Units

Every six months Pump pulleys,

belts, and belt
tension

1. Remove power to the unit.

• Owner—Inspect
• ASC/CSC only—Repair

and test

CAUTION

To prevent an injury, remove power to the pump/dispenser
before you start the maintenance activity.

WARNING

CAUTION

To avoid injury, avoid getting your fingers in a pinch point
between the pulley and belt during an inspection.

CAUTION

2. Inspect belts for fraying/cracks.
3. Inspect pulleys for excessive wear in grooves and

excessive bearing play.

4. Ensure that there is no more than one inch of play

on either side of the belt, by pressing the belt
midway between the two pulleys.

Note: If repair is required, call an ASC/CSC.

CAUTION

Do not attempt to make these repairs yourself. Doing so could
result in severe injury or death.

WARNING

Every six months Nozzle hooks

and shafts

1. Lubricate with silicone grease, if required.
2. Check for damage.
3. Ensure that the locking tab locator is not broken.

The locking tab locator helps hold the nozzle in
the nozzle boot and enables the station owner to
lock the nozzle boot with a clasp padlock.

Note: If repair is required, call an ASC/CSC.

• Owner—Inspect
• ASC/CSC only—Repair

and test

CAUTION

Do not attempt to make these repairs yourself. Doing so could
result in severe injury or death.

WARNING

Every six months Door locks

Lubricate with a graphite lubricant or lock oil. Follow
manufacturer’s instructions. Do not over-lubricate.

Owner

Every 12 months
or as required in
harsh climate

Polish unit

Polish metal parts with Nu Finish

car polish. Do not

use automobile wax. Refer to

“Performing General

and Component Maintenance Inspections”

page 32

Owner

Recommended
Frequency

Components

Recommended Maintenance

Who Performs the
Inspection/Repair

Содержание eclipse













































































Результаты поиска

Содержание eclipse

Отзывы:

Fujitsu eclipse, Руководство по эксплуатации, Страница: 45 / 76

Результаты поиска

Содержание eclipse

Отзывы: