manualshive.com logo in svg

Fujitsu eclipse, Руководство по эксплуатации, Страница: 41 / 76

Поделиться
Скачать
Fujitsu eclipse Скачать руководство пользователя страница 41

MDE-3893P Encore® and Eclipse® Series Owner’s Manual · December 2011

Page 37

Periodic Inspections

Maintaining Units

Once a week, or 
as notified about 
a potential leak

Leaks, outside 
the unit

1. Inspect the following for leaks or signs of leakage:

 • Breakaways
 • Couplings
 • Hose outlet castings
 • Hoses
 • Nozzles
 • Swivels

2. Look for any signs of fuel or fuel staining around 

the base of the dispenser, especially at the side 
columns and at the upper housing.

3. Review all documentation provided by each 

component’s manufacturer for additional 
inspection information. 

4. If a leak is found, stop using the unit, and make 

arrangements to repair the leak.

CAUTION

If you find a leak, stop using the pump/dispenser, and contact 
your local ASC/CSC. Fire, explosion, or electrical shock could 
result, if you continue to use a damaged pump/dispenser.

WARNING

CAUTION

Do not attempt to make these repairs yourself. Doing so could 
result in severe injury or death.

WARNING

• Owner—Inspect
• ASC/CSC only—Repair 

and test

Once a week or 
after drive-offs 

Breakaways

1. Inspect breakaways for secure connection to 

hose and for any leaks.

CAUTION

If you find a leak, stop using the pump/dispenser, and contact 
your local ASC/CSC. Fire, explosion, or electrical shock could 
result, if you continue to use a damaged pump/dispenser.

WARNING

2. Consult the breakaway manufacturer for any 

additional required inspections.

Notes: 
1. If repair is required, call an ASC/CSC.
2. Some breakaways are not repairable. Check with 

the ASC/CSC whether the breakaway is 
repairable before the ASC/CSC attempts to 
reassemble the breakaway.

3. A leak inspection within the hydraulics cabinet is 

also required. See the relevant section, later in 
this chapter.

CAUTION

Do not attempt to make these repairs yourself. Doing so could 
result in severe injury or death.

WARNING

• Owner—Inspect
• ASC/CSC only—Repair 

and test

Once a week or 
as required

Wash unit

Clean with Simple Green

®

 all purpose cleaner (or 

equivalent). Do not wash with a high pressure hose. 
Refer to 

“Performing General and Component 

Maintenance Inspections”

 on 

page 32

.

Owner

Recommended 
Frequency

Components

Recommended Maintenance

Who Performs the 
Inspection/Repair

Содержание eclipse













































































Отзывы:

Нет отзывов