Fujitsu eclipse Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 76

Fujitsu eclipse Скачать руководство пользователя страница 44

Maintaining Units

Periodic Inspections

Page 40

MDE-3893P Encore® and Eclipse® Series Owner’s Manual · December 2011

After first filter
change—Every
300,000 gallons
(1.1 million
liters), every six
months, or when
fuel delivery rate
significantly
slows.

CAUTION

Do not attempt to perform any of these tasks yourself.
Performing these tasks incorrectly could result in severe injury
or death.

WARNING

Note: Most complaints regarding continual slow flow rate from the dispenser are

caused by clogged filters

Every three
months

Clean CRIND
device printer

• Clean the CRIND device M00317A00X printer

using the printer cleaning card Q13400. Follow
instructions in

“Cleaning the CRIND Device in

the M00317A00X Printer”

(use

Moore Wallace M05194B001).

• Clean the CRIND device M04119A001 (USB)

printer using the M05194B001 cleaning kit.
Follow instructions included in the kit.

Owner

Every three
months

Clean CRIND
device display

Clean the CRIND device display regularly with a
mild detergent and soft cloth using Moore Wallace
M05194B001 cleaning kit. Be careful not to scratch
the display. Do not use an abrasive cleaner, or glass
cleaner or detergent that contains ammonia.
Ammonia will damage plastic display windows and
door materials.

Owner

Every six months Inspect and

lubricate
Shear Valves

To check valve operation, perform the following
tasks:
1. Trip the valve.
2. Authorize the hose at the console, if required.
3. Lift the operating handle.
4. Place the discharge nozzle in an approved

container.

5. Squeeze the nozzle operating lever. If flow

continues after several seconds, the valve is
defective and must be serviced or replaced.

6. Place a few drops of SAE10 oil on Shear Valve

body shaft.

7. Open and close valve with a wrench several

times.

8. Place valve back in service.

Note: If repair is required, call an ASC/CSC.

• Owner—Inspect and

lubricate

• ASC/CSC only—Repair

If you are not sure which device is the Shear Valve or have not
been trained regarding its use or service, have the ASC/CSC
inspect and lubricate this device for you.

CAUTION

CAUTION

Do not attempt to make these repairs yourself. Doing so could
result in severe injury or death.

WARNING

Recommended
Frequency

Components

Recommended Maintenance

Who Performs the
Inspection/Repair

«
...
42
43
44
45
46
...
»

Содержание eclipse













































































Отзывы:

Нет отзывов