background image

En-22

Air Filter Maintenance

Wash the air filters with water if small dust particles remain on the air filters even after automatic filter cleaning is per-
formed.

It is recommended to perform dust box maintenance when the air filter maintenance is performed.

1. Open the front panel, and then remove

the dust boxes and air filters.

Refer to procedure 1 in Dust Box Maintenance (page 19).

2. Remove the air filters from the dust boxes.

Refer to procedure 1 in Dust Box Maintenance (page 19).

3. Remove the dust with a vacuum cleaner,

and then wash the air filters with water.

 Wipe the air filters with a towel, etc., after washing

them with water, and then place them in a shaded area
to dry.

  Do not bend the air filters. The air filters may be dam-

aged and prevent the automatic filter cleaning from
being performed. Be especially careful not to damage
the teeth of the rack on the back of each air filter.

Air filter backside

Rack (bar with teeth)

 Do not clean the air filters with any abrasive or hard

object. The air filters may be damaged.

  Do not clean with hot water above 60°C.

  Do not dry with hot air from a hair dryer, etc. The air

filters may be deformed.

 After washing the air filters with water, do not force-

fully shake them dry. The air filters may be damaged.

4. Install the air filters in the dust boxes.

Refer to procedure 3 in Dust Box Maintenance (page 21).

5. Install the dust boxes and air filters in the

indoor unit, and then close the front panel.

Refer to procedure 4 in Dust Box Maintenance (page 21).

  If automatic filter cleaning is not performed normally

after performing air filter maintenance (automatic fil-
ter cleaning stops during filter cleaning or the air fil-
ters do not come out, etc.), remove the dust boxes
and air filters and install them again.

Indoor Unit Maintenance

Remove the dust from the exterior of the indoor unit with
a vacuum cleaner, wipe the unit with lukewarm water,
and then dry with a clean, soft cloth.

Do not clean with water above 40°C. The exterior of the
indoor unit may be deformed and become discolored.

Do not clean with benzene, paint thinner, or polish. They
will damage the exterior of the indoor unit.

PERFORMING MAINTENANCE (CONTINUED)

9312556014-En.pm6.5

2003.6.11, 5:08 PM

22

Содержание AWY14LSACW

































Отзывы: