manualshive.com logo in svg

Fujitsu AWY14LSACW, Руководство по эксплуатации

Поделиться
Скачать
Fujitsu AWY14LSACW Скачать руководство пользователя страница 24

En-21

3. Assemble the dust boxes, and install the air filters.

1. Assemble each dust box.

1

 Place the front casing facing down and insert the pro-

jection on the rear case into the hole in the front case.

Rear case
(dark blue)

Projection

Front case 
(light blue)

●

  When putting the front and rear cases together, make

sure that the brush holders are not sticking out.

2

 WMake sure the side of the rear case with the tab over-

laps the front case and then install the rear case.

Latch

“Click”

Rear case

Front case

2. Install the air filters in the dust boxes.

1

 Align the insertion directions written on each dust box

and air filter, and then insert the air filter into the dust
box between the front and rear cases.

Air filter

Dust box

Dust box

Air filter

●

  When inserting the air filter, make sure it is not upside

down or backwards, and then install correctly. If the air
filter is not installed correctly, the indoor unit may
malfunction.

●

  The air filter will be difficult to insert if you are pressing

down on the dust box.

2

 Insert the air filter until it stops.

4.  Install the dust boxes and air filters in the Indoor Unit, and then press the MAINTENANCE/

MANUAL AUTO button.

1. Install the dust boxes and air filters in the

indoor unit.

●

 When installing the dust boxes, make sure that the two

latches (yellow) on the ends of each dust box are open. If
the dust boxes are installed with the latches closed, the
indoor unit may malfunction.

1

 Open the front panel, grab the holding position on

each air filter, and then insert each filter into the in-
door unit until it stops.

Open the
latches.

Open the
latches.

2

 Install the dust boxes and close the two latches (yel-

low) on the ends of each dust box.

Latch

“Click”

●

  If the air filters are hanging out of the indoor unit when

the dust boxes and air filters are filters are installed, re-
move the dust boxes and air filters and install them again.

2. Plug the power supply cord into the elec-

trical outlet and press the MAINTENANCE/
MANUAL AUTO button.

After installing the dust boxes, plug the power supply
cord into the electrical outlet, and then press the MAIN-
TENANCE/MANUAL AUTO button on the Indoor Unit for
about 1 second.

MAINTENAN
CE/MANUAL 
AUTO button
(Press for 1 
second.)

MANUAL AUTO 
operation
(Press for 3 seconds.)

“Beep”

*   The MAINTENANCE Indicator Lamp (red)

will go out,if it is lit at this time.

●

  Press the MAINTENANCE/MANUAL AUTO button and

release it after a beeping sound is produced. If the
MAINTENANCE/MANUAL AUTO button is pressed for
over 3 seconds, MANUAL AUTO operation will begin
(see page 15).

●

  Be sure to press the MAINTENANCE/MANUAL AUTO

button after completing MAINTENANCE. If the MAINTE-
NANCE Indicator Lamp (red) remains on, automatic
filter cleaning will not be performed.

3. Close the front panel.

9312556014-En.pm6.5

2003.6.11, 5:08 PM

21

Содержание AWY14LSACW

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды