Fujitsu AOU18RLXFW Скачать руководство пользователя страница 16

Страница: 16 / 66

20. DEFROST OPERATION CONTROL

01-13

1. CONDITION OF STARTING THE DEFROST OPERATION

Integratingdefrost

(Constant monitoring)

If the compressor continuous operation time is less than 10 minutes,

the OFF number of the compressor is counted.

If any defrost operated, the compressor OFF count is cleared.

2. CONDITION OF THE DEFROST OPERATION COMPLETION

Defrost operation is released when the conditions becomes as shown in Table 17.

( Table 17 : Condition of defrost release )

Release Condition

Outdoor heat exchanger temperature is higher than 55.4°F(13°C)

Compressor operation time has passed 15 minutes.

The defrost operation starts as shown in the following Table 14, 15, and 16.

From 2nd and later

defrost after

starting operation

Less than 35 minutes

More than 35 minutes

Does not operate

Compressor integrating operation time

( Table 14 : Condition of 1st defrost operation)

1st defrost

after

starting operation

Compressor integrating operation time

Less than 22 minutes

More than 22 minutes

More than 62 minutes

Does not operate

Outdoor heat exchanger temperature

Below 15.8°F (-9°C )

Outdoor heat exchanger temperature

Below 21.2°F (-6°C)

Outdoor heat exchanger temperature

Below 23°F (-5°C )

More than 210 minutes

( For long continuous operation )

Less than 10 minutes

( For

intermittent operation )

Compressor integrating operation time

Outdoor heat exchanger temperature

Below 26.6°F (-3°C)

OFF count of the compressor

40 times

( Table 16 : Condition of Integrating defrost operation)

( Table 15 : Condition of 2nd defrost operation)

Содержание AOU18RLXFW



































































Результаты поиска

Содержание AOU18RLXFW

Отзывы:

Похожие инструкции для AOU18RLXFW

Бренды по названию

Популярные бренды

Fujitsu AOU18RLXFW, Инструкция по эксплуатации

Результаты поиска

Содержание AOU18RLXFW

Отзывы:

Похожие инструкции для AOU18RLXFW

Бренды по названию

Популярные бренды