Fujitsu AOU18RLXFW Скачать руководство пользователя страница 17

Страница: 17 / 66

01-14

3. Defrost Flow Chart

The defrosting shall proceed by the integrating operation time, outdoor temperature

and outdoor heat exchanger temperature as follows.

(Not defrosted for 10 minutes)

Heating operation start : Compressor ON

Outdoor heat exchanger temperature: Over 55° F(13°C)

Compressor ON time: Maximum 15 minutes

Defrost end

Compressor

integrating

operation:

Over 22 minutes

Compressor

integrating

operation:

Over 62 minutes

Outdoor

heat exchanger

temperature:

Below 15.8°F(- 9°C)

Outdoor

heat exchanger

temperature:

Below 23°F(- 5°C)

Compressor

integrating

operation:

Over 35 minutes

2nd and later defrost

Compressor : OFF

Outdoor fan motor : OFF

30 sec later 4-way valve : OFF

35 sec later compressor : ON

Compressor

integrating

operation:

Over 210 minutes

Integrating defrost

(Constant monitoring)

Defrost Indicator:

[Operation lamp]

7 sec ON / 2 sec OFF

Defrost start

Outdoor

heat exchanger

temperature:

Below 21.2°F(- 6°C)

Outdoor

heat exchanger

temperature:

Below 26.6°F(- 3°C)

Compressor

OFF count :

40 times

1st defrost

Содержание AOU18RLXFW



































































Результаты поиска

Содержание AOU18RLXFW

Отзывы:

Похожие инструкции для AOU18RLXFW

Бренды по названию

Популярные бренды

Fujitsu AOU18RLXFW, Инструкция по эксплуатации

Результаты поиска

Содержание AOU18RLXFW

Отзывы:

Похожие инструкции для AOU18RLXFW

Бренды по названию

Популярные бренды