Fujitsu AOU18RLXFW Скачать руководство пользователя страница 24

Страница: 24 / 66

Trouble shooting 1

OUTDOOR UNIT Error Method:

Detective Actuators:

Detective details:

Forecast of Cause:

Indicate or Display:

Refer to error code table.

YES

Serial Communication Error

(Serial Reverse Transfer Error)

Outdoor unit Main PCB

Outdoor unit Fan motor

1. Connection failure 2. External cause 3. Main PCB failure 4. Active filter module failure

5. Transistor PCB (IPM) failure 6. Filter PCB failure 7. Outdoor unit Fan motor failure

Check Point 1-1 : Reset the power and operate

Does error indication reappear?

Check Point 1-2 : Check external cause such as noise

Check if the ground connection is proper.

Check if there is any equipment that causes harmonic wave

near the power cable (Neon light bulb or any electronic

equipment which causes harmonic wave).

Check Point 2 : Check connection

Check any loose or removed connection line of

between indoor unit and outdoor unit.

>> If there is an abnormal condition, correct it by

referring to Installation Manual or Data &

Technical Manual.

Check connection condition in control unit.

(If there is loose connector, open cable or mis-wiring)

Check Point 3 : Check the voltage of power supply

Check the voltage of power supply

>> Check if AC187V(AC208V-10%) - 253V(10%) appears

at outdoor unit terminal L1 - L2.

When the indoor unit cannot receive the serial signal from Outdoor unit

more than 2minutes after power ON, or the indoor unit cannot receive

the serial signal more than 15seconds during normal operation.

02-03

2-2 TROUBLE SHOOTING WITH ERROR CODE

Check Point 4 : Check serial signal (Reverse transfer signal)

Check serial signal (Reverse transfer signal)

>> Check if indicated value swings between AC70V and AC130V at outdoor unit terminal 1 - 3.

>> If it is abnormal, Check the parts as follows.

- Outdoor unit fan motor (PARTS INFORMATION 5)

- Active filter module (PARTS INFORMATION 4)

- Transistor PCB (IPM) (PARTS INFORMATION 7)

- Filter PCB (Check the wire of CN110)

>> If Outdoor fan motor is abnormal, replace Outdoor unit fan motor and Main PCB.

>> If Active filter module or IPM is abnormal, replace it.

>> If the parts are normal, replace Main PCB.

1
2
3

L1
L2

RED

WHITE

BLACK

WHITE

Содержание AOU18RLXFW



































































Результаты поиска

Содержание AOU18RLXFW

Отзывы:

Похожие инструкции для AOU18RLXFW

Бренды по названию

Популярные бренды

Fujitsu AOU18RLXFW, Инструкция по эксплуатации

Результаты поиска

Содержание AOU18RLXFW

Отзывы:

Похожие инструкции для AOU18RLXFW

Бренды по названию

Популярные бренды