Fujitsu Siemens Computers D1419 Скачать руководство пользователя страница 10

Important notes

2 - English

A26361-D1419-Z120-1-7419

The shipped version of this board complies with the requirements of the EEC
directive 89/336/EEC "Electromagnetic compatibility".

Compliance was tested in a typical PC configuration.

When installing the board, refer to the specific installation information in the
operating manual or technical manual for the receiving device.

Connecting cables for peripherals must be adequately shielded to avoid interference.

!

Components can become very hot during operation. Ensure you do not touch
components when making extensions to the mainboard. There is a danger of burns!

i

The warranty is invalidated if the device is damaged during the installation or
replacement of system expansions. Information on which system expansions you can
use is available from your sales outlet or the customer service centre.

Information about boards

To prevent damage to the mainboard, the components and conductors on it, please take great care
when you insert or remove boards. Take great care to ensure that extension boards are slotted in
straight, without damaging components or conductors on the mainboard, or any other components,
for example EMI spring contacts.

Remove the plug from the mains outlet so that system and mainboard are totally disconnected from
the mains voltage.

Be careful with the locking mechanisms (catches, centering pins etc.) when you replace the
mainboard or components on it, for example memory modules or processors.

Never use sharp objects (screwdrivers) for leverage.

Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown.

When you handle boards fitted with ESDs, you must, under all circumstances,
observe the following:

You must always discharge static build up (e.g. by touching a grounded object)
before working.

The equipment and tools you use must be free of static charges.

Remove the power plug from the mains supply before inserting or removing
boards containing ESDs.

Always hold boards with ESDs by their edges.

Never touch pins or conductors on boards fitted with ESDs.

Содержание D1419

































Отзывы: